NAL A3LA-RS Скачать руководство пользователя страница 49

Страница: 49 / 101

NAL Research Corporation (TN2012-02-V1.0)

NOTE:

For the proper operation of the IRLP procedures, t2 should be less than t1 and 2*t4

should be less than t1.

Read Command:

+WIRLP?

Query the actual IRLP parameters resulting from the negotiation (XID exchange) at the start of

the most recent data call. Note that these may differ from the desired parameters set using
“+WIRLP=…”; from power-up they are set to hardcoded defaults, and will only change as the
result of the negotiation. The response is in the form:

+WIRLP: <ver>, <k1>, <k2>, <t1>, <n2>, <t2>, <r1>, <r2>, <t4>, <mode>

Test Command:

+WIRLP=?

List the supported IRLP parameter settings. The response is in the form:

+WIRLP: (supported <ver>s), (supported <k1>s), (supported <k2>s), (supported <t1>s),

(supported <n2>s), (supported <t2>s), (supported <r1>s), (supported <r2s), (supported

<t4>s), (supported <mode>s)

A.8.81 +WFRNG – Force IRLP Renegotiation

Set Command:

+WFRNG=<frng>

Set forced renegotiation of IRLP parameters.
<frng> can take the following values:

Do not renegotiate (default)

Renegotiate

Disconnect

Read Command:

+WFRNG?

Query the current parameter setting. The response is in the form:

+WFRNG: <frng>

Test Command:

+WFRNG=?

List the supported parameter settings. The response is in the form:

+WFRNG: (supported <frng>s)

A.8.82 +WTM – IRLP Test Mode

Set Command:

+WTM=<tm>

Select DCE mode of operation.
<tm> can take the following values:

IRLP test mode off (default)

IRLP test mode on

Read Command:

+WTM?

Query the current parameter setting. The response is in the form:

+WTM: <tm>

Test Command:

+WTM=?

List the supported parameter settings. The response is in the form:

+WTM: (supported <tm>s)

Содержание A3LA-RS






































































































Результаты поиска

Содержание A3LA-RS

Отзывы:

NAL A3LA-RS, Общее описание устройства, Страница: 49 / 101

Результаты поиска

Содержание A3LA-RS

Отзывы: