MW TOOLS TIG 200 PAC, Руководство пользователя

Страница: 42 / 86

42
M1.3.TIG200PAC.NLFREN 21052019
FR
18
/
50
E201 SC-A0
10.3.3 Welding Parameters Setting
Press rotary encoder potentiometer to adjust welding parameters based on actual demands. The
parameters’ setting can be done during no load or in the middle of welding without affecting welding.
Welding
mode
Torch
switch
mode
Pre-flow
Initial
current
Up
slope
time
Peak
current
Background
current
AC
frequency
Balance
MMA NO × × ×
●
× × ×
DC TIG
2T
● ● ● ●
× × ×
4T
● ● ● ●
× × ×
Spot
welding
● ● ● ● ●
× ×
DC Pulse
TIG
2T
● ● ● ● ●
× ×
4T
● ● ● ● ●
× ×
Spot
welding
● ● ● ● ●
× ×
AC TIG
2T
● ● ● ● ● ● ●
4T
● ● ● ● ● ● ●
Spot
welding
● ● ● ● ● ● ●
AC Pulse
TIG
2T
● ● ● ● ● ● ●
4T
● ● ● ● ● ● ●
Spot
welding
● ● ● ● ● ● ●
Adjusting direction
Welding
mode
Torch
switch
mode
Arc
forc
e
curr
Spot
welding
time
Down
slope
time
Pulse
frequency
Pulse
width
Pilot
arc
current
Post-flow
Tungsten
electrodes
or
electrodes
19 / 50
E201 SC-A0
Notes
：
1.
●
means available,
×
means null.
2. Press rotary knob for a continuous 2 seconds enters interlock mode; if the indicator is not in peak current
and stop spinning rotary knob, it will go back to peak current position after 10 seconds.
3. Electrodes selection function is for choosing a suitable welding parameter; eg. arc start current, welding
current range; if the electrode chosen by operator doesn’t match electrode parameters on the control panel,
will illuminate yellow, which means the welding performance is being affected; so only with the
suitablew electrode parameter and welding current, can light off and to achieve the best welding
performance.
4. When switch welding modes, if part of parameters are the same, then there is no need to change the
ent selection
MMA NO
●
× × × × × ×
●
DC TIG
2T × ×
●
× ×
● ● ●
4T × ×
●
× ×
● ● ●
Spot
welding
× ×
● ● ● ● ● ●
DC Pulse
TIG
2T × ×
● ● ● ● ● ●
4T × ×
● ● ● ● ● ●
Spot
welding
×
● ● ● ● ● ● ●
AC TIG
2T × ×
●
× ×
● ● ●
4T × ×
●
× ×
● ● ●
Spot
welding
×
● ● ● ● ● ● ●
AC Pulse
TIG
2T × ×
● ● ● ● ● ●
4T × ×
● ● ● ● ● ●
Spot
welding
×
● ● ● ● ● ● ●
Adjusting direction
Notes:
1. signifie disponible, x signifie nul.
2. Pressez le bouton rotatif pendant 2 seconde pour entrer en mode verrouillage. Si l’indicateur n’est pas en courant de crête
et que vous arrêtez de tourner le bouton rotatif, il va retourner en position de courant de crête après 10 secondes.
3. La fonction de sélection des électrodes sert à choisir un paramètre de soudage adapté, par exemple le courant de
démarrage de l’arc ou la plage de courant de soudage. Si l’électrode choisi par l’opérateur ne correspond pas
aux paramètres de l’électrode au panneau de contrôle, le signal va s’allumer en jaune, ce qui signifie que les
performan ces de soudage en seront affectées. Seul le choix des paramètres de l’électrode et du courant de soudage
correspondant permettra d’éteindre le signal et d’optimiser les performance de soudage.
4. Lors de la modification des modes de soudage, si une partie des paramètres sont les mêmes, il n’est pas nécessaire de
modifier ces paramètres durant les réglages, et ces paramètres se modifieront automatiquement en fonction des limites des
modes.
19
/
50
E201 SC-A0
Notes
：
1.
●
means available,
×
means null.
2. Press rotary knob for a continuous 2 seconds enters interlock mode; if the indicator is not in peak current
and stop spinning rotary knob, it will go back to peak current position after 10 seconds.
3. Electrodes selection function is for choosing a suitable welding parameter; eg. arc start current, welding
current range; if the electrode chosen by operator doesn’t match electrode parameters on the control panel,
will illuminate yellow, which means the welding performance is being affected; so only with the
suitablew electrode parameter and welding current, can light off and to achieve the best welding
performance.
4. When switch welding modes, if part of parameters are the same, then there is no need to change the
ent selection
MMA NO
●
× × × × × ×
●
DC TIG
2T × ×
●
× ×
● ● ●
4T × ×
●
× ×
● ● ●
Spot
welding
× ×
● ● ● ● ● ●
DC Pulse
TIG
2T × ×
● ● ● ● ● ●
4T × ×
● ● ● ● ● ●
Spot
welding
×
● ● ● ● ● ● ●
AC TIG
2T × ×
●
× ×
● ● ●
4T
× ×
●
× ×
● ● ●
Spot
welding
×
● ● ● ● ● ● ●
AC Pulse
TIG
2T
× ×
● ● ● ● ● ●
4T × ×
● ● ● ● ● ●
Spot
welding
×
● ● ● ● ● ● ●
Adjusting direction
19 / 50
E201 SC-A0
Notes
：
1.
●
means available,
×
means null.
2. Press rotary knob for a continuous 2 seconds enters interlock mode; if the indicator is not in peak current
and stop spinning rotary knob, it will go back to peak current position after 10 seconds.
3. Electrodes selection function is for choosing a suitable welding parameter; eg. arc start current, welding
current range; if the electrode chosen by operator doesn’t match electrode parameters on the control panel,
will illuminate yellow, which means the welding performance is being affected; so only with the
suitablew electrode parameter and welding current, can light off and to achieve the best welding
performance.
4. When switch welding modes, if part of parameters are the same, then there is no need to change the
ent selection
MMA NO
●
× × × × × ×
●
DC TIG
2T × ×
●
× ×
● ● ●
4T × ×
●
× ×
● ● ●
Spot
welding
× ×
● ● ● ● ● ●
DC Pulse
TIG
2T × ×
● ● ● ● ● ●
4T × ×
● ● ● ● ● ●
Spot
welding
×
● ● ● ● ● ● ●
AC TIG
2T × ×
●
× ×
● ● ●
4T × ×
●
× ×
● ● ●
Spot
welding
×
● ● ● ● ● ● ●
AC Pulse
TIG
2T × ×
● ● ● ● ● ●
4T × ×
● ● ● ● ● ●
Spot
welding
×
● ● ● ● ● ● ●
Adjusting direction
Mode de
soudage
Soudage
par points
Soudage
par points
Soudage
par points
Soudage
par points
Sens de réglage
Mode de
commuta-
tion de la
torche
C
our
an
t ar
c f
or
ce
Temps de
soudage
par points
Temps
de
down-
slope
Fréquence
d’impulsion
Largeur
d’impul-
sion
Courant
d’arc
pilote
Post-flow
Électrodes
ou électrodes
tungstène
Non
copyrighted
document
- all
rights
reserved
by
FBC