MULTIQUIP QP3Ti Скачать руководство пользователя

Страница: 32 / 54

PAGE 32 — QP3Ti TRASH PUMP • OPERATION AND PARTS MANUAL — REV. #1 (05/07/18)

TROUBLESHOOTING (PUMP)

Troubleshooting (Trash Pump)

Symptom

Pilot Lamp Status

Possible Problem

Solution

Pump does not take on water

(MANUAL mode).

Green lamp stays on, when

engine starts and red lamp

starts flashing, when pump

does not take on water in 5

minutes.

Not enough priming water in the

housing?

Add water.

Engine speed too low?

Increase throttle.

Strainer plugged?

Clean strainer.

Suction hose damaged?

Replace or repair hose, and clamps.

Air leak at suction port?

Check that fittings are tight and properly

sealed.

Pump is located too high above water

line?

Move pump closer to water.

Debris collecting in pump housing?

Clean pump housing.

Too much distance between impeller and

volute?

Adjust clearance by adding shims or

replace impeller. Min. .006 inch - Max.

.020 inch

Water leaking out weep hole between

pump and engine?

Check condition of mechanical seal and

gaskets, between pump end and engine

housing.

Pump does not take on water

(AUTO mode).

Green lamp stays on, when

engine starts and red lamp

starts flashing, when pump

does not take on water in 5

minutes.

Not enough priming water in the

housing?

Add water.

Strainer plugged?

Clean strainer.

Suction hose damaged?

Replace or repair hose, and clamps.

Air leak at suction port?

Check that fittings are tight and properly

sealed.

Pump is located too high above water

line?

Move pump closer to water.

Debris collecting in pump housing?

Clean pump housing.

Too much distance between impeller and

volute.

Adjust clearance by adding shims or

replace impeller. Min. .006" - Max. .020".

Water leaking out weep hole between

pump and engine?

Check condition of mechanical seal and

gaskets, between pump end and engine

housing.

Pump takes in water, little or

no discharge.

Green lamp stays on.

Engine speed too low

(MANUAL mode)?

Increase throttle speed

(MANUAL mode).

Suction strainer partially plugged?

Clean strainer.

Impeller/Volute worn?

Adjust clearance by adding shims or

replace impeller/volute.

Suction hose leaks at inlet.

Green lamp stays on.

Fittings/clamps are not sealed properly?

Tighten, replace or add clamp. (Keep

extra seals on pump).

Hose diameter is too large?

Use smaller diameter hose or replace

hose.

Discharge does not stay on

coupling.

Green lamp stays on.

Pressure too high?

Check pressure, add additional clamp.

Hose kinked or end blocked?

Check hose.

Impeller does not turn, pump

is hard to start.

Green and red lamps OFF.

Impeller jammed or blocked?

Open pump cover and clean dirt and

debris from inside housing.

Impeller and volute binding?

Adjust clearance by removing shim from

behind impeller.

Defective engine?

See Engine Owner's Manual.

Содержание QP3Ti























































Результаты поиска

Содержание QP3Ti

Отзывы:

Похожие инструкции для QP3Ti

Бренды по названию

Популярные бренды

MULTIQUIP QP3Ti, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание QP3Ti

Отзывы:

Похожие инструкции для QP3Ti

Бренды по названию

Популярные бренды