MULTIQUIP QP3Ti Скачать руководство пользователя

Страница: 31 / 54

QP3Ti TRASH PUMP • OPERATION AND PARTS MANUAL —REV. #1 (05/07/18) — PAGE 31

TROUBLESHOOTING (ENGINE)

Troubleshooting (Engine) - continued

Symptom

Pilot Lamp Status

Possible Problem

Solution

Weak in power,

compression is proper and

does not misfire.

Green lamp stays on.

Air cleaner clogged?

Clean or replace air cleaner.

Air in fuel line?

Bleed (remove air) from fuel line.

Fuel level in carburetor float chamber
improper?

Adjust carburetor float.

Carbon deposits in cylinder?

Clean or replace cylinder.

Weak in power,

compression is proper but

misfires.

Green lamp stays on.

Ignition coil defective?

Flush fuel system and replace with

fresh fuel.

Ignition plug often shorts?

Replace ignition wires, clean ignition.

Fuel in use inadequate (water, dust)?

Flush fuel system and replace with

fresh fuel.

Engine overheats.

Green lamp stays on.

Excessive carbon deposition in

combustion chamber?

Clean or replace crankcase.

Exhaust or muffler clogged with carbon?

Clean or replace muffler.

Spark plug heat value incorrect?

Replace spark plug with correct type

spark plug.

Rotational speed

fluctuates.

Green lamp stays on.

Fuel flow erratic?

Check fuel line.

Air taken in through suction line?

Check suction line.

Engine running and then

stopped suddenly

Red lamp flashes 2 times

Low fuel or No fuel?

Add fuel.

Oil Alert lamp On and red

lamp flashes 2 times and

repeats.

Low oil or No oil?

Add oil.

Red lamp flashes 3 times

and repeats.

Harness disconnected?

Repair harness connection.

Operation not satisfactory

under DRAIN mode

operation

Green lamp stays on.

Float switch connection failure?

Check for proper connection of float
switch.

Green and red lamps flash
in 0.5 sec interval.

Float switch connection failure
(upside down installation of upper/bottom
float switches)?

Correct connection of float switches.

Green lamp stays on.

Float switch cable disconnected/broken?

Replace float switch cable.

Operation Not satisfactory

under FILL mode

operation

Green lamp stays on.

Float switch connection failure?

Check for proper connection of float
switch.

Green and red lamps flash
in 0.5 sec interval.

Float switch connection failure
(upside down installation of upper/bottom
float switches)?

Correct connection of float switches.

Green lamp stays on.

Float switch cable disconnected/broken?

Replace float switch cable.

Содержание QP3Ti























































Результаты поиска

Содержание QP3Ti

Отзывы:

Похожие инструкции для QP3Ti

Бренды по названию

Популярные бренды

MULTIQUIP QP3Ti, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание QP3Ti

Отзывы:

Похожие инструкции для QP3Ti

Бренды по названию

Популярные бренды