MULTIQUIP QP3Ti Скачать руководство пользователя

Страница: 20 / 54

PAGE 20 — QP3Ti TRASH PUMP • OPERATION AND PARTS MANUAL — REV. #1 (05/07/18)

SETUP

7. The discharge side may utilize proper discharge hoses,

PVC pipe, or concrete pipe.

8. Check that discharge hoses lay flat and as straight as

possible. Remove any sharp bends or kinks from the

hose so the water flow cannot be blocked.

9. Once the engine is started; and depending on the

application set-up, the priming process will take a few

moments before water begins to flow.

10. The performance of the pump (Flow, Head, Water

Velocity, and Pressure) is dependent on the many

factors that surround the application. These factors

include, but are not limited to: operating altitude, suction

lift, discharge and suction hose diameter and length,

overall friction loss coefficients, the specify gravity of

the fluid to be pumped, the fluid temperature, and total

discharge head.

CAUTION

The strainer should be positioned so it will remain

completely

under water

. Running the pump with the

strainer above water for long periods can damage the

pump.

1. It is advantageous to place the pump as close as

possible to the water source (Figure 7) on a solid,

level operating surface. The most critical factor for

successful pump operations is not to exceed 25’ Total

Suction Lift (at sea level).

2. Ensure that the pump has the proper level of fuel and

engine oil.

3. Initially prime the pump by removing the fill cap (see

Figure 3) and filling the casing with water. If the pump

casing is not filled with water prior to operations, it will

not be able to start the pumping process and you risk

overheating the mechanical seal assembly.

4. Attach the proper suction and discharge hoses to the

pump ports. Ensure that the hose O-rings are in place,

and that hose do not show any cracks, gouges, or

holes. The hoses should not be kinked, and must be

secured tightly to their respective ports.

5. A proper suction hose is commonly reinforced with rigid

PVC helix and is specifically designed to safeguard

against collapsing during pumping operations. It is

essential that the pump utilize a suction hose with the

same diameter as the suction port.

6. Ensure that the strainer is placed on the end of the

suction hose, and that the hose is placed in the water

source in such a manner as not to bury the strainer

into sand or silt.

Figure 8. Pump Placement

Содержание QP3Ti























































Результаты поиска

Содержание QP3Ti

Отзывы:

Похожие инструкции для QP3Ti

Бренды по названию

Популярные бренды

MULTIQUIP QP3Ti, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание QP3Ti

Отзывы:

Похожие инструкции для QP3Ti

Бренды по названию

Популярные бренды