manualshive.com logo in svg

MTU 12V4000C*5 series, Руководство по эксплуатации

Поделиться
Скачать
MTU 12V4000C*5 series Скачать руководство пользователя страница 74

5.6 Engine – Starting in manual mode

Preconditions

☑

Engine is not under load.

☑

External start interlock is not activated.

DANGER

Rotating and moving engine parts.
Risk of crushing, danger of parts of the body being caught or pulled in!
• Before cranking the engine with starter system, make sure that there are no persons in the engine's

danger zone.

WARNING

High level of engine noise when the engine is running.
Risk of damage to hearing!
• Wear ear protectors.

NOTICE

Re-starting the engine following an automatic safety shutdown.
Risk of severe engine damage!
• Before starting the engine, make sure the root cause of the safety shutdown was eliminated.
• If the root cause cannot be identified or eliminated, contact Service.

Preparation

Item

Action

Operating mode switch (if
applicable).

Change to manual mode.

Coolant preheating unit (if
applicable).

Switch on

Starting the engine

Item

Action

Control cabinet, control pan-
el etc. (depending on manu-
facturer).

1. If a coolant preheater unit is available, ensure that the coolant tempera-

ture is > 40 °C.

2. Press start button.

• Automatic starting sequence is executed.
• Engine speed instrument indicates increasing speed.
• After the starting sequence is completed, engine runs at idle speed.

72 | Operation | MS15041/03E 2018-08

TIM-ID: 0000002233 - 007

Содержание 12V4000C*5 series


















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды