manualshive.com logo in svg

MTU 12V4000C*5 series, Руководство по эксплуатации

Поделиться
Скачать
MTU 12V4000C*5 series Скачать руководство пользователя страница 183

13.

Tighten screw on hold-down clamp (→ Step 9) to specified torque using a torque wrench.

Name

Size

Type

Lubricant

Value/Standard

Screw

M12

Tightening torque

(Engine oil)

100 Nm +10 Nm

14.

Tighten adapter (1) tighten to specified torque using a torque wrench.

Name

Size

Type

Lubricant

Value/Standard

Adapter

M18

Tightening torque

(Engine oil)

100 Nm +10 Nm

Note:

Ensure immaculate cleanliness.

15.

Coat thread and sealing cone of HP line (3) with engine oil.

16.

Tighten union nuts (2, 5) on HP line (3) to specified torque using a torque wrench. Tightening sequence:

1 Nut on adapter (2), counterhold on adapter (1)
2 Nut on rail (5)

Name

Size

Type

Lubricant

Value/Standard

Union nut / thrust
screw

M12

Tightening torque

(Engine oil)

40 Nm +5 Nm

17.

Release union nuts (2, 5) on HP line (3) approx. 45° angle of rotation while counterholding adapter (1) in
relation to injector.

18.

Tighten union nuts (2, 5) on HP line (3) without interruption once again to specified final tightening torque
using a torque wrench. Tightening sequence:

1 Nut on adapter (2), counterhold on adapter (1)
2 Nut on rail (5)

Name

Size

Type

Lubricant

Value/Standard

Union nut / thrust
screw

M12

Tightening torque

(Engine oil)

40 Nm +5 Nm

19.

Install return line (6) and tighten union nuts.

20.

Fit connectors on injector (arrowed).

Note:

If the drift correction (CDC) is not reset, the
emission certification becomes invalid.

21.

Reset drift correction (CDC) with DiaSys®
(→ Dialog system DiaSys® E531920/..). If
DiaSys® is not available, contact Service.

Final steps

1.

Install cylinder head cover (→ Page 172).

2.

Open fuel supply to engine.

MS15041/03E 2018-08

| Injector | 181

TIM-ID: 0000053873 - 004

Содержание 12V4000C*5 series


















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды