manualshive.com logo in svg

MTU 12V4000C*5 series, Руководство по эксплуатации

Поделиться
Скачать
MTU 12V4000C*5 series Скачать руководство пользователя страница 192

8.9.4 Additional fuel filter – Replacement

Preconditions

☑

Engine is stopped and starting disabled.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Filter wrench

F30379104

1

Engine oil
Easy-change filter

(→ Spare Parts Catalog)

2

WARNING

Fuels are combustible and explosive.
Risk of fire and explosion!
• Avoid open flames, electrical sparks and ignition sources.
• Do not smoke.
• Wear protective clothing, protective gloves, and safety glasses / facial protection.

WARNING

Liquid or gaseous media, e.g. fuel, are poisonous.
Escaping vapors of highly volatile media, e.g. fuel or ether.
Risk of fatal injury through swallowing; risk of poisoning through inhalation; irritation to eyes
and skin!
• Seek medical attention immediately; do not induce vomiting.
• Do not inhale vapors or mist.
• Wear protective clothing, protective gloves, and safety glasses.
• If contact is made with skin, wash off with water and soap.

Replacing additional fuel filter

1.

Provide suitable container to collect escaping
fuel.

2.

Use filter wrench to remove easy-change fil-
ter (2).

3.

Clean sealing face on filter head (1).

4.

Coat gasket on easy-change filter (2) with
thin layer of engine oil (arrow).

5.

Screw on easy-change filter (2) by hand until
the seal makes contact with the filter head
and tighten manually.

6.

Replace other easy-change filters in the same
way.

7.

Vent fuel system (→ Page 182).

190 | Fuel Filter | MS15041/03E 2018-08

TIM-ID: 0000063488 - 002

Содержание 12V4000C*5 series


















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды