manualshive.com logo in svg

MTU 12V4000C*5 series, Руководство по эксплуатации

Поделиться
Скачать
MTU 12V4000C*5 series Скачать руководство пользователя страница 197

8.11.2 Exhaust flaps – Checking coupling rod clearance and function

Preconditions

☑

Engine is stopped and starting disabled.

☑

No operating voltage applied.

WARNING

Actuation mechanism in the exhaust and intake area closes automatically.
Risk of crushing hands!
• To carry out the teach-in routine, keep clear of the safety zone of the actuation mechanism in the

intake and exhaust area.

• Switch off the operating voltage of the engine governor before starting the mechanical test.
• Wear protective goggles.

WARNING

Hot components/surfaces.
Risk of burns!
• Allow the engine to cool down to below 50 °C before beginning work.
• Wear suitable protective equipment/thermal gloves.
• Avoid unprotected contact with hot surfaces.

Checking coupling rods (bypass and EGR flap) – mechanical

Note:

For installation position of exhaust flaps, refer to overview (→ Page 192).

1.

Remove guard plates of exhaust flaps (→ Page 197).

2.

Check operability and ease of movement of
coupling rod (1) by moving it at the specified
points (arrows) and make sure that there is
no excessive play.

Result:

Replace coupling rod (1) if it is jamming, slug-
gish or features excessive play (→ Page 197).

3.

Check whether the internal spring pulls the
flap into the F-position:
• Fail-safe position for bypass flap and EGR

shutoff flap: opened.

• Fail-safe position for donor cylinder flap:

closed.

Result:

If the bypass flap/EGR shutoff flap is closed
or the donor cylinder flap is opened, contact
Service.

Checking coupling rod (donor cylinder flap) – mechanical

Note:

For installation position of exhaust flaps, refer to overview (→ Page 192).

1.

Remove guard plates of exhaust flaps.

MS15041/03E 2018-08

| Exhaust Gas Recirculation | 195

TIM-ID: 0000060224 - 001

Содержание 12V4000C*5 series


















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды