manualshive.com logo in svg

MTU 12V4000C*5 series, Руководство по эксплуатации

Поделиться
Скачать
MTU 12V4000C*5 series Скачать руководство пользователя страница 22

2.3 Crankshaft – Transport locking device

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Torque wrench, 10–60 Nm

F30452769

1

Torque wrench, 60–320 Nm

F30452768

1

Ratchet adapter

F30027340

1

Engine oil

Transport locking device

Note:

The locking device protects the crankshaft bearings from shocks and vibration damage during engine trans-
port.

For removal and installation of the transport locking device, observe the following:
• The transport locking device must remain installed as long as possible during engine installation in order

to avoid damage.

• Starting or barring the engine is allowed only with the transport locking device removed. If the generator/

gearbox is installed, ensure that the transport locking device of the generator/gearbox is removed.

• Prior to transport of the engine, always install the transport locking device according to the specifications.
• If the generator/gearbox is installed and also has to be moved, install transport locking device of genera-

tor/gearbox.

• Always use the screws supplied with or installed in the transport locking device to secure it on the engine.
• Fit this documentation in an easily visible place on the engine.

Removing transport locking de-
vice on driving end (KS), variant
A

1.

Remove parts (1) to (8) from engine. Spacer
sleeves (5) are optional.

2.

Store the removed parts of the transport
locking device for possible reuse.

20 | Transport | MS15041/03E 2018-08

TIM-ID: 0000060211 - 003

Содержание 12V4000C*5 series


















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды