manualshive.com logo in svg

MTU 12V4000C*5 series, Руководство по эксплуатации

Поделиться
Скачать
MTU 12V4000C*5 series Скачать руководство пользователя страница 145

5220 – AL IAP Sensor Cyl B10 Defect

Cause

Corrective action

The signal from the single
accumulator pressure sensor
(B97.B10) in injector B10 is faulty
or missing.

u

Contact Service.

5221 – AL No Injection Detected CylA1

Cause

Corrective action

The pressure variation measured
at sensor B97A1 and evaluated by
the EXU indicates that despite
correct energization no fuel is
being injected at cylinder A1.

1. Check whether alarm 5201 is signaled. If so, contact Service.
2. Replace injector (→ Page 176).
3. Contact Service.

5222 – AL No Injection Detected CylA2

Cause

Corrective action

The pressure variation measured
at sensor B97A2 and evaluated by
the EXU indicates that despite
correct energization no fuel is
being injected at cylinder A2.

1. Check whether alarm 5202 is signaled. If so, contact Service.
2. Replace injector (→ Page 176).
3. Contact Service.

5223 – AL No Injection Detected CylA3

Cause

Corrective action

The pressure variation measured
at sensor B97A3 and evaluated by
the EXU indicates that despite
correct energization no fuel is
being injected at cylinder A3.

1. Check whether alarm 5203 is signaled. If so, contact Service.
2. Replace injector (→ Page 176).
3. Contact Service.

5224 – AL No Injection Detected CylA4

Cause

Corrective action

The pressure variation measured
at sensor B97A4 and evaluated by
the EXU indicates that despite
correct energization no fuel is
being injected at cylinder A4.

1. Check whether alarm 5204 is signaled. If so, contact Service.
2. Replace injector (→ Page 176).
3. Contact Service.

MS15041/03E 2018-08

| Troubleshooting | 143

TIM-ID: 0000065298 - 004

Содержание 12V4000C*5 series


















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды