manualshive.com logo in svg

MTU 12V4000C*5 series, Руководство по эксплуатации

Поделиться
Скачать
MTU 12V4000C*5 series Скачать руководство пользователя страница 283

7

Industrial Pro  

Installation Instructions

Primer Pump Service

 

E

WARNING:

 Fuels are combusible. 

•  RISK OF FIRE OR EXPLOSION:

•  Avoid open flames, electrical sparks or igni-

tion sources

•  Do not smoke.

Disassembly

1.  Open the vent cap and then open the drain valve - 

drain the Industrial Pro below the primer pump con-
nections points.

2.  Close the drain valve. Dispose of the fuel in an envi-

ronmentally safe manner.

3.  Disconnect the primer pump electrical connection.
4.  Disconnect the fuel hoses at the fittings on the primer 

pump.

5.  Remove the fittings (use backup wrench as needed) 

and set aside for later use. If the unit has 90° fittings, 
note the fitting orientation.

6.  Remove the fitting on the end of the pump using two 

wrenches to hold the end stationary as the fitting is 
loosened. See Figure 6.

7.  The washer on the fittings MUST be in place when 

reassembled. 

Washer

Figure 6 – Removing the Primer Pump Fitting

8.  Remove the primer pump mounting strap bolts and 

straps.

9.  Remove primer pump.

Assembly

1.  Install the new primer pump with fuel flow arrow aimed 

towards fuel outlet. (See Figure 7)

FUEL 

OUT

FUEL 

OUT

Figure 7 - Primer Pump

2.  Install the primer pumps straps and bolts and torque 

to 8-10 ft-lbs.

3.  Install the primer pump fittings aimed as originally 

installed (noted during disassembly).

Figure 8 - Primer Pump Location

4.  Torque the primer pump fitting jam nuts to 10-15 ft-lbs 

(use backup wrench as needed).

5.  Connect the fuel hoses to the primer pump and torque 

to 10-15 ft-lbs (use backup wrench as needed).

6.  Connect the primer pump electrical connection.

Priming

Use primer pump to prime the Industrial Pro or follow man-
ual process listed below.
1.  Prime the unit by filling the clear cover with clean die-

sel fuel until it reaches the top of the filter.

2.  Install the vent cap.
3.  Start the engine and run for one minute.
4.  Slowly open the vent cap and allow the fuel to drop to 

about one inch above the collar.

5.  Close the vent cap. 

Note: 

It is normal for the fuel level to vary after the initial 

start-up and during.

MS15041/03E 2018-08

| Manufacturer's Documentation | 281

TIM-ID: 0000083486 - 002

Содержание 12V4000C*5 series


















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды