MTU 12V4000C*5 series Скачать руководство пользователя страница 166

Страница: 166 / 305

Unscrew locknut (1) and remove together
with washer (2).

Remove filter cover (3), cover (4) and sealing
ring (5).

Remove threaded rod (6).

Replace oil mist fine separator (7).

Replace sealing ring (5) if necessary.

10.

Install sealing ring (5), cover (4) and filter
cover (3).

11.

Fit new locknut (1) and new washer (2) and tighten locknut (1) with torque wrench to specified tightening
torque.

Name

Size

Type

Lubricant

Value/Standard

Locknut

M10

Tightening torque

10 Nm ±2 Nm

12.

Replace further oil mist fine separators in the same way.

164 | Crankcase Breather | MS15041/03E 2018-08

TIM-ID: 0000062822 - 002

Содержание 12V4000C*5 series


















































































































































































































































































































Результаты поиска

Содержание 12V4000C*5 series

Отзывы:

Бренды по названию

Популярные бренды

MTU 12V4000C*5 series, Руководство по эксплуатации

Результаты поиска

Содержание 12V4000C*5 series

Отзывы:

Бренды по названию

Популярные бренды