MTU 12 V 2000 P12 Скачать руководство пользователя страница 49

Страница: 49 / 187

Item

Color

Inscription

Meaning / Function

White

DIMMER ↓

Holding down the key decreases LCD background illumina‐

tion.

White

LAMP TEST

Pressing the key initiates lamp test.

Red

TEST OVER‐

SPEED

Pressing the key initiates overspeed test.
LED (spot) lights up as long as the overspeed test is run‐

ning.

Green

(none)

Green

(none)

Green

(none)

White

ENGINE SPEED

INCREASE

Engine speed is increased as long as the key is held down.

White

ENGINE SPEED

DECREASE

Engine speed is decreased as long as the key is held down.

Green

READY FOR OP‐

ERATION

Pressing the key causes changeover between “Not ready

for operation” and “Ready for operation” status.
LED (spot) lights up at "Ready for operation" switch posi‐

tion.

Green

LOCAL OPERA‐

TION

Pressing the key switches between local operation and re‐

mote control.
LED (spot) lights up when local mode is active.

White

START

Pressing the key initiates automatic engine starting proce‐

dure.
LED (spot) lights up as long as the starting procedure is

running.

White

STOP

Pressing the key initiates automatic engine stopping proce‐

dure.
Spot LED lit when stop signal is applied (also from remote

control system).

Red

EMERGENCY

STOP

Pressing the key initiates an immediate emergency engine

stop.
LED (spot) flashes once the emergency stop has been trip‐

ped and until the alarm has been acknowledged.

MS150025/02E 2012-10 | Operation | 49

TIM-ID: 0000008856 - 004

Содержание 12 V 2000 P12




























































































































































































Результаты поиска

Содержание 12 V 2000 P12

Отзывы:

Похожие инструкции для 12 V 2000 P12

Бренды по названию

Популярные бренды

MTU 12 V 2000 P12, Руководство по эксплуатации

Результаты поиска

Содержание 12 V 2000 P12

Отзывы:

Похожие инструкции для 12 V 2000 P12

Бренды по названию

Популярные бренды