MTU 12 V 2000 P12 Скачать руководство пользователя страница 78

Страница: 78 / 187

Fault

code

Alarm text

Meaning

Task

201

SD T-COOLANT Sensor defect (coolant tem‐

perature)

1. Check wiring.

2. Contact Service.

202

SD T-FUEL

Sensor defect (Fuel tempera‐

ture)

1. Check wiring.

2. Contact Service.

203

SD T-CHARGE

AIR

Sensor defect (charge-air

temperature)

1. Check wiring.

2. Contact Service.

205

SD T-COOLANT

INTERC.

Sensor defect (charge-air

coolant temperature)

1. Check wiring.

2. Contact Service.

208

SD P-CHARGE

AIR

Sensor defect (charge-air

pressure)

1. Check wiring.

2. Contact Service.

211

SD P-LUBE OIL

Sensor defect (lube oil pres‐

sure)

1. Check wiring.

2. Contact Service.

216

SD T-LUBE OIL

Sensor defect (lube oil tem‐

perature)

1. Check wiring.

2. Contact Service.

220

SD COOLANT

LEVEL

Sensor defect (coolant level)

1. Check wiring.

2. Contact Service.

229

SD ENG.SPEED

SENSORS

Sensor defect (crankshaft

speed) and sensor defect

(camshaft speed)

1. Check wiring.

2. Contact Service.

230

SD CRANK‐

SHAFT SPEED

Sensor defect (crankshaft

speed)

1. Check wiring.

2. Contact Service.

231

SD CAMSHAFT

SPEED

Sensor defect (camshaft

speed)

1. Check wiring.

2. Contact Service.

245

SD POWER

SUPPLY

Sensor defect (ECU operating

voltage)

Contact Service.

246

SD T-ELEC‐

TRONIC

Sensor defect (temperature in

ECU)

Contact Service.

250

SD CAN SPEED

DEMAND

Sensor defect (CAN nominal

speed demand)

1. Check speed transmitter.

2. Check wiring (CAN bus).

3. Contact Service.

266

SD SPEED DE‐

MAND AN.

Sensor defect (analog nomi‐

nal speed demand)

1. Check speed transmitter.

2. Check wiring.

3. Contact Service.

267

SP.DEM.TEST

BENCH

Sensor defect (analog speed

demand);
NOTE:
Only used in test-stand opera‐

tion.

1. Check speed transmitter.

2. Check wiring.

3. Contact Service.

270

SD SPEED DE‐

MAND FI1

Sensor defect (frequency in‐

put for speed demand);

1. Check speed transmitter.

2. Check wiring.

3. Contact Service.

271

SD T-EXTERN 1 External device defective

(CAN T-EXTERN 1)

Contact Service.

272

SD T-EXTERN 2 External device defective

(CAN T-EXTERN 2)

Contact Service.

273

SD P-EXTERN 1 External device defective

(CAN P-EXTERN 1)

Contact Service.

78 | Troubleshooting | MS150025/02E 2012-10

TIM-ID: 0000003157 - 001

Содержание 12 V 2000 P12




























































































































































































Результаты поиска

Содержание 12 V 2000 P12

Отзывы:

Похожие инструкции для 12 V 2000 P12

Бренды по названию

Популярные бренды

MTU 12 V 2000 P12, Руководство по эксплуатации

Результаты поиска

Содержание 12 V 2000 P12

Отзывы:

Похожие инструкции для 12 V 2000 P12

Бренды по названию

Популярные бренды