MTU 12 V 2000 P12 Скачать руководство пользователя страница 52

Страница: 52 / 187

4.4 Start engine in manual mode (testing mode)

Preconditions

☑ Generator (if provided) not connected to network.
☑ External start interlock is not activated.

DANGER

Unguarded rotating and moving engine components.

Risk of serious injury – danger to life!

• Before barring or starting the engine, make sure that nobody is in the danger zone.

WARNING

Engine noise above 85 dB (A).

Risk of damage to hearing!

• Wear ear protectors.

Preparation

Item

Task

Operating mode selector

switch (if provided)

Change to manual mode.

Preheating pump (if provid‐

ed)

Switch ON.

Starting the engine

Item

Task

Switchgear cabinet, control

panel etc. (depending on

manufacturer)

If coolant temperature is

• > 40 °C (with preheating equipment), or

• > 5 °C (without preheating equipment):
Press start button.

• Automatic starting sequence is performed;

• Engine speed display instrument indicates increasing crankshaft speed;

• After the starting sequence is completed, engine is running at rated

speed.

Connect generator to network (if provided), run engine to reach operating

temperature )

Item

Task

Switchgear cabinet, control

panel etc. (depending on

manufacturer)

Close the generator circuit breaker.

Engine

Apply full load only after engine has reached operating temperature (cool‐

ant temperature approx. 75 °C).

52 | Operation | MS150025/02E 2012-10

TIM-ID: 0000002226 - 002

Содержание 12 V 2000 P12




























































































































































































Результаты поиска

Содержание 12 V 2000 P12

Отзывы:

Похожие инструкции для 12 V 2000 P12

Бренды по названию

Популярные бренды

MTU 12 V 2000 P12, Руководство по эксплуатации

Результаты поиска

Содержание 12 V 2000 P12

Отзывы:

Похожие инструкции для 12 V 2000 P12

Бренды по названию

Популярные бренды