MTU 12 V 2000 P12 Скачать руководство пользователя страница 25

Страница: 25 / 187

2.4 ECS-5 – Use of devices

Engine governor

Central control and monitoring device for the engine
• Communication with other devices and higher-level systems via CAN bus.

• Control of injection system.

• Control of up to 20 injectors.

• Acquisition and evaluation of engine operating states.

• Monitoring of limit values.

• Self-monitoring and diagnosis,

• integral status/fault display

• fault memory

• Extensive I/O features:

• Plant side 13 inputs, 10 outputs, 2 serial interfaces,

• engine side 26 inputs, 26 outputs.

• Engine and plant-related setting variables in exchangeable memory modules.

• In case of inadmissible states and limit value violations: Initiation of power reduction, engine stop and

emergency engine stop (configurable).

• Diagnosis via RS232 interface for dialog unit.
Software structure:

Name

Meaning

Download software

For downloading firmware and configuration data.

Dialog software

For the dialog with a PC or notebook.

Automation software for open-loop control.

E.g. to control injection quantity.

Automation software for monitoring.

E.g. for engine stop and emergency engine stop.

Communication software

For communication with other devices and via the

CAN bus.

MS150025/02E 2012-10 | General Information | 25

TIM-ID: 0000009426 - 001

Содержание 12 V 2000 P12




























































































































































































Результаты поиска

Содержание 12 V 2000 P12

Отзывы:

Похожие инструкции для 12 V 2000 P12

Бренды по названию

Популярные бренды

MTU 12 V 2000 P12, Руководство по эксплуатации

Результаты поиска

Содержание 12 V 2000 P12

Отзывы:

Похожие инструкции для 12 V 2000 P12

Бренды по названию

Популярные бренды