manualshive.com logo in svg

MTF DP C10, Инструкция по эксплуатации

Поделиться
Скачать
MTF DP C10 Скачать руководство пользователя страница 21

EN - 21 

 

 

◆

 

Selection of Support Levels 

When the display is turned on, press the   or   (<0.5s) button to switch to the support level, the 

lowest level is 0, the highest level is 5. When the system is switched on, the support level starts in 

level 1. There is no support at level 0.  

 

◆

 

Selection Mode 

Briefly press the   (0.5s) button to see the different trip modes. 
Trip: daily kilometers (TRIP) - total kilometers (ODO) - Maximum speed (MAX) - Average speed 

(AVG) - Range (RANGE) - Energy consumption (CALORIES(only with torque sensor fitted)) - 

Travel time (TIME). 

 

 

◆

 

Headlights / backlighting 

Hold the   (>2s) button to activate the headlight and taillights.

 Hold the   (>2s) button again to 

turn off the headlight. The brightness of the backlight can be set in the display settings 
"Brightness". If the display /Pedelec is switched on in a dark environment, the display 

backlight/headlight will automatically be switched on. If the display backlight/headlight has been 

manually switched off, the automatic sensor function is deactivated. You can only turn on the light 

manually. After switching on the system again. 

 

 

If the front or rear light is not connected, the button can only be used to switch the display backlight on 

/ off.

 

Содержание DP C10




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды