manualshive.com logo in svg

MRC STE-V100, Руководство пользователя, Страница: 19 / 22

Поделиться
Скачать
MRC STE-V100 Скачать руководство пользователя страница 19

he door’s micro-switch loose,

misplace 

switch 

Under the condition of

warming, Pressure and

temperature do not rise,

or rise slowly

1.Control circuit of the heater

shorts out or burns down

2.pipe joint or safety valve

leaks seriously

1.Check and change the

damaged elements

2.check, tighten the pipe joint,

safety valve, etc

Under the condition of

drainage, Pressure and

temperature do not drop,

or drop slowly

Drain Filter clogs

Clear up the sundries on the

filter valve core

Fail to reach the

sterilization temperature

Whether determined by the
boiling point of the altitude.

Please check the set

temperature of the boiling

point

If not the reason of the

altitude, please contact us or

our distributor

Safety Valve opens

1.Whether the pressure is

too high?

2.Whether the safety valve

breaks down ?

1.Adjust temperature

departure

2. Adjust and change safety

valve

Steam leaking

1.

W

hether door rubber gasket

become hard and aged?

2.

W

hether the door strip cracks?

3.Whether door rubber

gasket falls off?

1. should change door rubber

gasket 

2.should change door rubber

gasket 

3. re-install door rubber

gasket 

2. Alarm Code:

When an error occurs during use, it shows the error code and the buzzer sounds

 

and indicates alarm, the sterilizer automatically stop moving, please look up the

 

following conditions and deal with them.

The failure code list

Failure code

Condition of the failure

 

Failure reason 

Содержание STE-V100























Отзывы:

Нет отзывов