Moyer Diebel 601HTG Скачать руководство пользователя страница 66

Страница: 66 / 114

Digital Temperature Display Codes

DISPLAY CODES

WASH TEMP

RINSE TEMP

WASH TEMP

RINSE TEMP

WASH TEMP

Booster Display Codes

CAUSE

Booster overtemp lockout

because booster temperature

is greater than 210˚F.

NOTE:

Booster is locked out

for 10 minutes before being

re-energized.

Booster therrmistor is

defective or disconnected,

broken wires.

NOTE:

After the therrmistor

is reconnected, there is a 5

second delay before the

display is re-energized.

Error Codes for Booster and Final Rinse Thermistors Only.

1 5 0

Both booster and final rinse

display thermistors are

defective, unplugged, or open

or broken wires between the

display and thermistor.

NOTE:

After a therrmistor

is reconnected, there is a 5

second delay before the

display is re-energized.

Содержание 601HTG



















































































































Результаты поиска

Содержание 601HTG

Отзывы:

Бренды по названию

Популярные бренды

Moyer Diebel 601HTG, Руководство пользователя

Результаты поиска

Содержание 601HTG

Отзывы:

Бренды по названию

Популярные бренды