Moyer Diebel 601HTG Скачать руководство пользователя страница 26

Страница: 26 / 114

The 601HTG pumps are located on

the left-side behind the lower front panel

of the dishwasher.

RINSE-AID

DETERGENT

1. The detergent and rinse-aid pumps are located on the lower left-side of the machine

behind the lower-front access panel.

2. Each pump is equipped with 6 feet [1.8 m] of pick-up tubes consisting of supply tubing,

stiffener tubes, and strainers.

3. The pick-up tubes are stowed on the back of the machine for shipping.
4. A red label marked DETERGENT and a blue label marked RINSE-AID identify the

chemical lines.

! VERY IMPORTANT !

ALWAYS USE A COMMERCIAL-GRADE NON-CHLORINATED DETERGENT.

PLACE THE CHEMICAL SUPPLY CONTAINERS AS CLOSE TO THE MACHINE AS POSSIBLE.

DO NOT ELEVATE THE CHEMICAL CONTAINERS ABOVE THE FINISHED FLOOR.

Chemical Dispensing Pumps

! VERY IMPORTANT !

Contact a chemical supplier for detergent and rinse-aid chemicals. The chemical supplier must

adjust the chemical dispensing pumps for water hardness and food soil types.

Chemical Connections

601HTG

Installation - Model 601HTG

Содержание 601HTG



















































































































Результаты поиска

Содержание 601HTG

Отзывы:

Бренды по названию

Популярные бренды

Moyer Diebel 601HTG, Руководство пользователя

Результаты поиска

Содержание 601HTG

Отзывы:

Бренды по названию

Популярные бренды