Moyer Diebel 601HTG Скачать руководство пользователя страница 11

Страница: 11 / 114

NOTE:

The installation of your dishwasher must be performed by qualified service personnel familiar

with food service equipment and must comply with all local health codes.

Problems due to improper installation are not covered by the Limited Warranty.

NOTE:

The installation of the dishwasher must comply with all local electrical, plumbing, health and

safety codes or in the absence of local codes, installed in accordance with the applicable

requirements in the National Electrical Code, NFPA 70, Canadian Electrical Code (CEC),

Part 1, CSA C22.1; and the Standard for Ventilation Control and Fire Protection of

Commercial Cooking Operations, NFPA 96.

CAUTION:

Be careful when lifting and moving the dishwasher to prevent damage to the machine.

Inspect the outside of the dishwasher carton for signs of damage.

Remove the carton and inspect the dishwasher for damage.

Check for any options or accessories that may have shipped with your dishwasher.

Compare the installation site utility connections with the dishwasher utility connections

and make sure they are the same.

The dishwasher can be installed as a free-standing unit or under a counter-top.

The typical counter-top height in most locations is 34" [86cm].

It is highly recommended that the

underside of the counter-top be clad

in metal.

Under counter installations should

provide storage space for the

dishwasher chemical supply

containers. Do not elevate the

containers above the finished floor.

Chemical supply containers should

be placed as close to the machine as

possible and the chemical tubing

taped to the back of the machine

should be repositioned before

permanently placing the machine.

Place the dishwasher in its permanent

location.

10.

The dishwasher has 4 adjustable feet

for leveling.

11.

Level the dishwasher front-to-back and side-to-side.

Receiving and Placement - Installation

Receiving - 601HTG, 601LTG

Counter-top

Wall

[8cm]

Min.

34"

[86cm]

Min.

Floor

Placement - 601HTG, 601LTG

Содержание 601HTG



















































































































Результаты поиска

Содержание 601HTG

Отзывы:

Бренды по названию

Популярные бренды

Moyer Diebel 601HTG, Руководство пользователя

Результаты поиска

Содержание 601HTG

Отзывы:

Бренды по названию

Популярные бренды