Moyer Diebel 601HTG Скачать руководство пользователя страница 28

Страница: 28 / 114

Model 601HTG - Installation

Pumps and Injection Points - Detergent and Rinse-aid Dispensing Pumps

601HTG

The chemical dispensing pump supply lines must be primed before they will pump the

chemicals properly.

Make sure the chemical containers are full and the correct pick-up tubes are in their

containers.

Turn the dishwasher power switch ON. The switch will illuminate and the dishwasher

will fill with water.

Open the dishwasher door, then push and hold the prime push button UP to the

DETERGENT position until detergent is observed entering the wash tank compartment

through the fitting located on the back right corner of the tank. Release the push button.

Push and hold the prime push button DOWN to the Rinse-aid position until you see

air bubbles moving through the rinse-aid tubing coming out of the chemical container.

Release the push button.

Close the door to complete the priming operation.

PRIME

DETERGENT

RINSE AID

! VERY IMPORTANT !

The chemical dispensing pumps must be primed before operating the dishwasher and

whenever the chemical container is changed.

Priming the Dispensing Pumps

Prime

Push button

PRIME

DETERGENT

RINSE AID

START

HEAVY DUTY

DELIME

WASH

RINSE

TEMPERATURE

1 8 0

1 5 0

OFF

DRAIN

POWER

Содержание 601HTG



















































































































Результаты поиска

Содержание 601HTG

Отзывы:

Бренды по названию

Популярные бренды

Moyer Diebel 601HTG, Руководство пользователя

Результаты поиска

Содержание 601HTG

Отзывы:

Бренды по названию

Популярные бренды