Moyer Diebel 601HTG Скачать руководство пользователя страница 18

Страница: 18 / 114

Installation - Model 601HTG

3. Disconnect the existing booster heater wires and change the booster heater element

jumpers as shown in the illustration below

4. Connect wires 1H1, 1H2, and 1H3 as shown below.

5. A replacement 3PH data plate is stowed on the back of the lower front access panel.
6. Replace the existing 1PH data plate on the front of the panel with the new 3PH data plate.

Discard the 1PH data plate.

7. Refer to the instructions on page 3 to connect the main incoming power to the

machine.

1H1

1H2

1H3

Booster Heater

Connected for 1PH

1H1

Booster Heater

Connected for 3PH

1H2

1H3

Wire not

connected

Wiring Diagram - Booster heater element connections shown for 1 phase and 3 phase operation.

Booster Heater Conversion from 1PH to 3 PH Operation

(continued)

! VERY IMPORTANT !

THE BOOSTER HEATER IS WIRED FOR 1PH OPERATION WHEN SHIPPED.

FOLLOW THE INSTRUCTIONS BELOW TO WIRE THE BOOSTER FOR 3PH.

Содержание 601HTG



















































































































Результаты поиска

Содержание 601HTG

Отзывы:

Бренды по названию

Популярные бренды

Moyer Diebel 601HTG, Руководство пользователя

Результаты поиска

Содержание 601HTG

Отзывы:

Бренды по названию

Популярные бренды