Moyer Diebel 601HTG Скачать руководство пользователя страница 46

Страница: 46 / 114

Installation - Model 601LTG

Drain Connection - 601LTG

(continued)

1. Install the drain hose to an 1-1/2" or larger "WYE" vented drain fitting.

2. CONNECTION TO A "TEE" FITTING WILL PREVENT THE DISHWASHER FROM

DRAINING COMPLETELY.

DO NOT

connect the dishwasher flexible

drain hose to a TEE drain fitting.

connect the dishwasher flexible drain

hose to a WYE drain fitting.

WYE

Fitting

Drain

Adapter

Fitting

Clamp

3/4" NPT Hose Barb

Fitting

Drain Hose

(Supplied by others)

For a Direct Drain Connection:

DO NOT REMOVE THE CLAMPS HOLDING THE DRAIN HOSE TO THE
BACK OF THE DISHWASHER.

DO NOT CONNECT THE DRAIN HOSE TO A DISPOSER.

DO NOT REDUCE THE SIZE OF THE DRAIN HOSE CONNECTION NOR USE A DOMESTIC
DRAIN FITTING.

DO NOT ADD ADDITIONAL LENGTH TO THE DRAIN HOSE.

DO NOT ALLOW THE DRAIN HOSE TO KINK.

NOTE

Plumbing connections must comply with national, provincial local plumbing and sanitary codes.

Содержание 601HTG



















































































































Результаты поиска

Содержание 601HTG

Отзывы:

Бренды по названию

Популярные бренды

Moyer Diebel 601HTG, Руководство пользователя

Результаты поиска

Содержание 601HTG

Отзывы:

Бренды по названию

Популярные бренды