Moyer Diebel 601HTG Скачать руководство пользователя страница 29

Страница: 29 / 114

Detergent and Rinse-aid Dispensing Pumps - Pump and Fill Adjustments

601HTG

Refer to the photo below:
1. The chemical dispensing pump run and the tank fill adjustment screws are located on the

end of the chemical circuit board swing-out bracket.

2. It is not necessary to swing the bracket out to make adjustments, but if desired, remove

the mounting nut (A) and swing the bracket (B) out and to the right.

3. Refer to the next page for adjustment instructions.

Installation - Model 601HTG

! VERY IMPORTANT !

Contact a chemical supplier for detergent and rinse-aid chemicals. The

chemical supplier must adjust the chemical dispensing pumps for water

hardness and food soil types.

! ATTENTION !

The amount of dispensed chemical is determined by the run time of the dispensing pump.

! VERY IMPORTANT !

INSPECT & REPLACE THE CHEMICAL DISPENSING PUMP SQUEEZE TUBES EVERY SIX MONTHS.

Содержание 601HTG



















































































































Результаты поиска

Содержание 601HTG

Отзывы:

Бренды по названию

Популярные бренды

Moyer Diebel 601HTG, Руководство пользователя

Результаты поиска

Содержание 601HTG

Отзывы:

Бренды по названию

Популярные бренды