Moxa Technologies AirWorks AWK-3121 Скачать руководство пользователя страница 7

Страница: 7 / 90

AirWorks AWK-3121 User’s Manual

Introduction

1-3

DIN-Rail or wall mounting ability

IP30 protected high-strength metal housing

Product Specifications

WLAN

Standards

IEEE 802.11a/g/b for Wireless LAN
IEEE 802.3u 10/100BaseT(X) for Ethernet LAN
EEE 802.3af for Power-over-Ethernet
IEEE 802.1D/w STP/RSTP

Spread Spectrum and
Modulation

DSSS with DBPSK, DQPSK, CCK
OFDM with BPSK, QPSK, 16QAM, 64QAM

Operating Channels
(Central Frequency)

US: 2.412 to 2.462 GHz (11 channels)

5.18 to 5.24 GHz (4 channels)

EU: 2.412 to 2.472 GHz (13 channels)

5.18 to 5.24 GHz (4 channels)

JP:

2.412 to 2.472 GHz (13 channels, OFDM)

2.412 to 2.484 GHz (14 channels, DSSS)

5.18 to 5.24 GHz (4 channels for W52)

Security 64-bit

and

128-bit

WEP encryption, WPA /WPA2

(IEEE 802.1X/ RADIUS, TKIP and AES)

Protocol

General Protocols:

Proxy ARP, DNS, HTTP, HTTPS, IP, ICMP, SNTP, TCP, UDP,
RADIUS, SNMP, RTP

AP-only Protocols:

ARP, BOOTP, DHCP, dynamic VLAN-Tags for 802.1X-Clients,
STP/RSTP (IEEE 802.1D/w)

Data Rates

802.11b: 1, 2, 5.5, 11 Mbps
802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54 Mbps

Transmit Power

802.11b: 1 to 11 Mbps: Typ. 18±1.5 dBm

802.11g: 6 to 24 Mbps: Typ. 18±1.5 dBm

36 to 48 Mbps: Typ. 16±1.5 dBm

54 Mbps: Typ. 15±1.5 dBm

802.11a: 6 to 24 Mbps: Typ. 16±1.5 dBm

36 to 48 Mbps: Typ. 14±1.5 dBm

54 Mbps: Typ. 13±1.5 dBm

Receiver Sensitivity

802.11b: -92 dBm @ 1 Mbps, -90 dBm @ 2 Mbps,

-88 dBm @ 5.5 Mbps, -84dBm @ 11 Mbps

802.11g:

-87 dBm @ 6 Mbps, -86 dBm @ 9 Mbps,

-85 dBm @ 12 Mbps, -82dBm @ 18 Mbps,

-80 dBm @ 24 Mbps, -76 dBm @ 36 Mbps,

-72dBm @ 48 Mbps, -70 dBm @ 54 Mbps

802.11a:

-87 dBm @ 6 Mbps, -86 dBm @ 9 Mbps,

-85 dBm @ 12 Mbps, -82dBm @ 18 Mbps,

-80 dBm @ 24 Mbps, -76 dBm @ 36 Mbps,

-72dBm @ 48 Mbps, -70 dBm @ 54 Mbps

Interface

Default Antenna

2dBi dual-band, Omni-directional antenna

Antenna Connector

RP-SMA (female)

Connection

10-pin Removable Terminal Block

Содержание AirWorks AWK-3121


























































































Результаты поиска

Содержание AirWorks AWK-3121

Отзывы:

Похожие инструкции для AirWorks AWK-3121

Бренды по названию

Популярные бренды

Moxa Technologies AirWorks AWK-3121, Руководство пользователя

Результаты поиска

Содержание AirWorks AWK-3121

Отзывы:

Похожие инструкции для AirWorks AWK-3121

Бренды по названию

Популярные бренды