Moxa Technologies AirWorks AWK-3121 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 90

background image

AirWorks AWK-3121 User’s Manual

Web Console Configuration

3-23

Fragment threshold

Setting

Description

Factory Default

Fragment Length
(256-2346)

This parameter specifies the maximum size
a data packet before splitting and creating
another new packet

2346

RTS threshold

Setting

Description

Factory Default

RTS/CTS Threshold
(256-2346)

This setting determines how large a packet
can be before the Access Point coordinates
transmission and reception to ensure
efficient communication

2346

NOTE

You can refer to the related glossaries in Chapter 5 for more detailed information about the
above-mentioned settings. By setting these parameters properly, you can better tune the
performance of your wireless network.

Transmission distance

Setting

Description

Factory Default

Distance or max. range
for transmission
(500-10000m)

The distance specifies the transmission
distance or max. range between two AWK
devices. This parameter should be set
properly, especially for long-distance
communication.

500

Transmission enhancement

Setting

Description

Factory Default

Enable/Disable

This setting can enhance communication by
strengthening the AWK-3121’s
transmission power. It is quite useful for
long-distance transmission or countering
environmental interference.

The user must

carefully evaluate and measure the
transmission power of the entire system to
make sure that it is still below the
regulative limit. Note, too, that RF type
802.11a mode cannot be used if this
function is enabled.

Disable

«
...
37
38
39
40
41
...
»

Содержание AirWorks AWK-3121



























































































Отзывы:

Нет отзывов

Похожие инструкции для AirWorks AWK-3121

Vb-C60 - Ptz Network Camera

Бренд: Canon Страницы: 30

Бренд: Xinje Страницы: 76

Бренд: Zenith Data Systems Страницы: 64

Бренд: ETAS Страницы: 69

Бренд: Macsense Страницы: 13

Бренд: Buffalo Страницы: 2

SLK-R602 Series

Бренд: Seriallink Страницы: 29

Бренд: Advantech Страницы: 36

Бренд: CELOT Страницы: 34

Бренд: Kaptia Страницы: 14

Бренд: SSV Embedded Systems Страницы: 17

Бренд: MFJ Страницы: 11

Бренд: Digisol Страницы: 81

Бренд: Rockwell Automation Страницы: 21

Бренд: Doro Страницы: 50

High-Precision AD/DA Board

Бренд: Waveshare Страницы: 8

Бренд: Airlink101 Страницы: 64

Бренд: ETAS Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды