Moxa Technologies AirWorks AWK-3121 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 90

background image

AirWorks AWK-3121 User’s Manual

Introduction

1-6

Beeper

The beeper signals that the system is ready with two short beeps.

Reset Button

The

RESET

button is located on the top panel of the AWK-3121. You can reboot the AWK-3121

or reset it to factory default settings by pressing the

RESET

button with a pointed object such as

an unfolded paper clip.

y

System reboot:

Hold the RESET button down for

under

5 seconds and then release.

y

Reset to factory default:

Hold the RESET button down for

over

5 seconds until the

STATE

LED starts blinking green. Release the button to reset the AWK-3121.

Relay (Digital Output)

The AWK-3121 has one relay output, which consists of the 2 terminal block contacts on the top
panel, as shown below. These relay contacts are used to forward system failure and
user-configured events.

The two wires attached to the relay contacts form an open circuit when a user-configured event is
triggered. If a user-configured event does not occur, the relay circuit will remain closed. For safety
reason, the relay circuit is kept open when the AWK-3121 is not powered.

«
...
8
9
10
11
12
...
»

Содержание AirWorks AWK-3121



























































































Отзывы:

Нет отзывов

Похожие инструкции для AirWorks AWK-3121

Бренд: D-Link Страницы: 267

TokenLink Velocity 3C319

Бренд: 3Com Страницы: 2

Бренд: Ubiquiti Страницы: 50

OXTOPUS EIA-709

Бренд: OCCITALINA Страницы: 54

ILDA Gem Laser projector tool

Бренд: Stanwax Laser Страницы: 3

Бренд: NETGEAR Страницы: 169

Scorpio WD2500BPVT

Бренд: Western Digital Страницы: 3

Scorpio WD2500BPVT

Бренд: Western Digital Страницы: 4

Бренд: Allied Telesis Страницы: 22

Бренд: TP-Link Страницы: 2

Бренд: Digi Страницы: 116

Бренд: Hamlet Страницы: 122

Бренд: Isee Страницы: 68

Бренд: S&T Страницы: 28

KÜHLER H2O 920

Бренд: Antec Страницы: 6

IA611 Xplained Pro

Бренд: Knowles Страницы: 14

Бренд: Renesas Страницы: 67

Бренд: Manson Engineering Industrial Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды