Moxa Technologies AirWorks AWK-3121 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 90

background image

AirWorks AWK-3121 User’s Manual

Introduction

1-5

Functional Design

LED Indicators

The LEDs on the front panel of the AWK-3121 allow you to identity the status and wireless
settings quickly.

The LED for

FAULT

indicates the system failure and

user-configured events. If the AWK-3121

cannot retrieve the IP address from a DHCP server, the

FAULT

LED will blink at an interval of

one second.

The LEDs for

SIGNAL

are a signal strength indicator and they merely function in

Client

mode.

The following table is a summary for the wireless settings and LED displays. You can check the
status of the AWK-3121 by reading these LEDs. More information about “Basic Wireless
Settings” is presented in Chapter 3.

Basic Wireless Settings

LEDs

Operation mode

WDS

CLIENT BRIDGE SIGNAL

Note

AP Disable

off

off -

AP

mode

AP Enable

off

on

-

Bridge mode: WDS is enabled

Client -

on

off

0

Client mode: no association

Client -

on

off 1

Client mode: associated, but poor
signal

Client -

on

off 2-5

Client mode: associated; signal is
fine

ATTENTION

When the LEDs for

FAULT

,

SIGNAL

,

CLIENT

,

BRIDGE

and

WLAN

all light up

simultaneously and blink at one-second interval, it means the system failed to boot. This may be
due to improper operation or uncontrollable issues, such as an unexpected shutdown during
firmware update. To recover the firmware, refer to “Firmware Recovery” in Chapter 6.

«
...
7
8
9
10
11
...
»

Содержание AirWorks AWK-3121



























































































Отзывы:

Нет отзывов

Похожие инструкции для AirWorks AWK-3121

EtherLink 3C509B

Бренд: 3Com Страницы: 8

Бренд: 3Com Страницы: 8

Бренд: Patton electronics Страницы: 8

LS42 - BladeCenter - 7902

Бренд: IBM Страницы: 56

Бренд: IBM Страницы: 2

BladeCenter Management Module

Бренд: IBM Страницы: 78

Бренд: IBM Страницы: 110

Remote Supervisor Adapter II

Бренд: IBM Страницы: 132

Бренд: Vanguard Страницы: 4

Бренд: Paradyne Страницы: 85

Бренд: Sangamo Страницы: 2

Бренд: Baicells Страницы: 10

COMMWARE ECHO 5G

Бренд: pivotal Страницы: 2

Бренд: Galaxy Страницы: 30

Бренд: Pressalit Care Страницы: 31

iCE40 SPRAM Series

Бренд: Lattice Semiconductor Страницы: 12

Бренд: ZALMAN Страницы: 18

3C8567 - SuperStack II NETBuilder SI 567...

Бренд: 3Com Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды