Moxa Technologies AirWorks AWK-3121 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 90

background image

AirWorks AWK-3121 User’s Manual

Web Console Configuration

3-13

WLAN Security Settings

The AWK-3121 provides four standardized wireless security modes: Open, WEP (Wired
Equivalent Privacy), WPA (Wi-Fi Protected Access) and WPA2. Several types of security models
are available in AWK-3121 by selecting

Security mode

and

WPA type

:

y

Open

: No authentication, no data encryption.

y

WEP

: Static WEP (Wired Equivalent Privacy) keys must be manually configured.

y

WPA/WPA2-Personal

: also known as WPA/WPA2-PSK. You need to specify the Pre-Shared

Key in the

Passphrase

field, which will be used by the TKIP or AES engine as a master key to

generate keys that actually encrypt outgoing packets and decrypt incoming packets.

y

WPA/WPA2-Enterprise

: also called WPA/WPA2-EAP (Extensible Authentication Protocol).

In addition to device-based authentication, WPA/WPA2-Enterprise enables user-based
authentication via IEEE802.1X. The AWK-3121 can support three EAP methods: EAP-TLS,
EAP-TTLS, and EAP-PEAP.

Security mode

Setting

Description

Factory Default

Open No

authentication

WEP Static

WEP

is

used

WPA

*

WPA is used

WPA2

*

Fully supports IEEE802.11i with
“TKIP/AES + 802.1X”

Open

* WPA and WPA2 cannot be supported in WDS (Bridge) mode.

Open

For security reasons, it is highly recommended that the security mode should be set to the options
other than Open System. When the security mode is set to Open System, no authentication or data
encryption will be performed.

«
...
27
28
29
30
31
...
»

Содержание AirWorks AWK-3121



























































































Отзывы:

Нет отзывов

Похожие инструкции для AirWorks AWK-3121

Ray 3 Plus Client

Бренд: Sun Microsystems Страницы: 6

Бренд: Data Translation Страницы: 60

Бренд: H3C Страницы: 22

Бренд: H3C Страницы: 3

Бренд: Paradyne Страницы: 2

Бренд: Paradyne Страницы: 20

Бренд: Paradyne Страницы: 2

Бренд: Zhone Страницы: 2

Бренд: Ubiquiti Страницы: 3

Бренд: IBM Страницы: 63

F-ZTAT H8/3048 Series

Бренд: Renesas Страницы: 34

Бренд: Tripp Lite Страницы: 20

Бренд: DPtech Страницы: 39

Бренд: KPN Страницы: 14

MegaRAID SCSI 320-2X

Бренд: LSI Страницы: 4

Бренд: C-Data Страницы: 26

Бренд: H3C Страницы: 12

Converter Board R0E5212BACFG00

Бренд: Renesas Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды