Moxa Technologies AirWorks AWK-3121 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 90

background image

AirWorks AWK-3121 User’s Manual

Web Console Configuration

3-31

RSTP Settings

(for AP mode only)

AWK-3121 supports IEEE802.1D Spanning Tree Protocol and IEEE802.1w Rapid STP standards.
In addition to eliminating unexpected path looping, STP/RSTP can provide a backup path recovery
if a wired/ wireless path fails accidentally. The reliability and availability can increase because this
fail-over function.

AWK-3121’s STP/RSTP feature is disabled by default. To be completely effective, you must
enable RSTP/STP on every AWK-3121 connected to your network. If AWK-3121 plays a

Client

role, which is connected to a device (PLC, RTU, etc.) as opposed to network switch equipment, it
is not necessary to enable STP/RSTP. The reason is that it will cause unnecessary negotiation.
AWK-3121s support STP/RSTP in

AP

mode (including WDS) only.

The following figures indicate which Spanning Tree Protocol parameters can be configured. A
more detailed explanation of each parameter is given below the figure.

RSTP status

This field will appear only when selected to operate STP/RSTP. It indicates whether this
AWK-3121 is the Root of the Spanning Tree (the root is determined automatically) or not.

Bridge priority

Setting

Description

Factory Default

Numerical value
selected
by user

You can increase the bridge priority by
selecting a lower number. A higher bridge
priority brings a greater chance of being
established as the root of the Spanning
Tree topology.

32768

Hello time

Setting

Description

Factory Default

Numerical value input
by user
(1 – 10 seconds)

The root of the Spanning Tree topology
periodically sends out a “hello” message to
other devices on the network to check if
the topology is healthy.

Hello time

indicates how often the root sends hello
messages.

2 (seconds)

«
...
45
46
47
48
49
...
»

Содержание AirWorks AWK-3121



























































































Отзывы:

Нет отзывов

Похожие инструкции для AirWorks AWK-3121

Express Ethernetwork DI-704P

Бренд: D-Link Страницы: 17

Бренд: D-Link Страницы: 11

Бренд: D-Link Страницы: 8

AirPlus DWL-810

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 84

Бренд: NEC Страницы: 47

Бренд: dbx Страницы: 2

Бренд: dbx Страницы: 17

Бренд: Quick Eagle Networks Страницы: 4

Бренд: SUNRICH TECHNOLOGY Страницы: 5

COMMWARE ECHO 5G

Бренд: pivotal Страницы: 2

Бренд: Moxa Technologies Страницы: 51

Бренд: Kaptia Страницы: 14

Бренд: Billion Страницы: 120

Бренд: Freescale Semiconductor Страницы: 8

NVRx-7300 series

Бренд: Swann Страницы: 9

OptiBond 210 C Series

Бренд: i-MO Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды