Moxa Technologies AirWorks AWK-1131A Скачать руководство пользователя страница 21

Страница: 21 / 82

AirWorks AWK-1131A

Web Console Configuration

3-4

Click on

SSID

for more detailed 802.11 Information, as shown in the following figure.

NOTE

The

802.11 Information

that is displayed might be different for different operation modes. For example,

Current BSSID

Signal strength

, and

SNR

are only available under Client operation modes.

General Setup

The General Setup group includes the most commonly used settings required by administrators to maintain
and control the AWK-1131A.

System Information

The

System Information

items, especially

Device name

and

Device description

, are displayed and

included on the

Overview

page, in SNMP information, and in alarm emails. Setting

System Information

items makes it easier to identify the different AWK-1131A units connected to your network.

Содержание AirWorks AWK-1131A


















































































Результаты поиска

Содержание AirWorks AWK-1131A

Отзывы:

Похожие инструкции для AirWorks AWK-1131A

Бренды по названию

Популярные бренды

Moxa Technologies AirWorks AWK-1131A, Руководство пользователя

Результаты поиска

Содержание AirWorks AWK-1131A

Отзывы:

Похожие инструкции для AirWorks AWK-1131A

Бренды по названию

Популярные бренды