Motorola Nitro SLX 5000 Скачать руководство пользователя страница 43

Страница: 43 / 44

Insert the connector in to the Power port on the bottom of the chassis.

IMPORTANT:

The connector latch must face the rear of the unit to enable potential

unlocking.

Slide the secondary lock/button to close the lever and secure the lock.

Figure 50: Securing the Housing Lock

CAUTION:

When securing the cable, ensure that there is no tension on the connector to

allow for easy disconnection and reconnection for maintenance.

3.8.6

Connecting Cables for Remote (External) Antenna Assembly

SLX 5000 can use remotely attached antennas.

Prerequisites:

Ensure that N-type Hellax RF cable (ordered separately) is available.

WARNING:

External antennas connected to SLX 5000 must be grounded.

Disconnect power to SLX 5000 before disconnecting the antenna.

CAUTION:

Cables for connection must be weather-proofed.

Follow the instructions of the antenna manufacturer to install remotely attached antennas.

Refer to

Antenna Connections for the Nitro System

in the

Nitro

™

System Planner

for additional

information on antenna connections.

Procedure:

Disconnect each of the RF cables that connect the integrated antenna to the unit.

Figure 51: Antenna RF Cables

Screw the protective cap on the integrated antenna cable to prevent environmental damage.

Weather-proof the protective caps with self-amalgamating tape and PVC tape.

MN007322A01-B

Chapter 3: SLX 5000 Installation

Содержание Nitro SLX 5000












































Результаты поиска

Содержание Nitro SLX 5000

Отзывы:

Похожие инструкции для Nitro SLX 5000

Бренды по названию

Популярные бренды

Motorola Nitro SLX 5000, Руководство по установке

Результаты поиска

Содержание Nitro SLX 5000

Отзывы:

Похожие инструкции для Nitro SLX 5000

Бренды по названию

Популярные бренды