Moretti Forni P110G C/A, Инструкция по эксплуатации, Страница: 12 / 42

UK/11
- Screw the cover back in place
5.3.2 REPLACING THE DOOR KNOB
After carrying out the operations described in 5.1 above, to replace the ball
knob proceed as follows:
- Open the doors of the proofer;
- Remove the plug (item 12 plate B);
- Unscrew the fixing nut inside the knob;
- Replace the knob (item 2 plate B) and tighten the fixing nut.
5.3.3 REPLACING THE THERMOSTAT
After carrying out the operations described in 5.1 above, to replace the
thermostat proceed as follows:
- Remove the electrical panel fixing screws.
- Disconnect the thermostat faston connectors.
- Remove the snap-on thermostat dial (item 5 plate B).
- Unscrew the ring nut (item 6 plate B) fixing the thermostat.
- Remove the thermostat sensor located inside the compartment.
- Replace the thermostat (item 7 plate B) and the relative sensor.
- Perform the above operations in reverse order to reassemble.
5.3.4 REPLACING THE MAGNETIC DOOR FASTENER
After carrying out the operations described in 5.1 above, to replace the
magnetic door fastener proceed as follows:
- Open the doors of the proofer;
- Remove the seal snap ring;
- Replace the magnetic door fastener.
5.3.5 REPLACING THE THERMOSTAT DIAL AND RING NUT
After carrying out the operations described in 5.1 above, to replace the
thermostat dial and/or relative ring nut, proceed as follows from the
outside of the compartment:
- Remove the snap-on thermostat dial (item 5 plate B).
- Unscrew the ring nut (item 6 plate B).
- Replace the ring nut and/or the dial.
5.3.6 REPLACING THE YELLOW INDICATOR LIGHT
AND/OR THE LIGHT SWITCH
After carrying out the operations described in 5.1 above, to replace the
yellow indicator light and/or the light switch proceed
as follows:
- Remove the control panel fixing screws.
- Disconnect the faston connectors for both the yellow indicator and the
light switch.
- Replace the yellow indicator light (item 14 plate B).
- Replace the light switch (item 4 plate B).
- Perform the above operations in reverse order to reassemble.
5.3.7
REPLACING THE HEATING ELEMENTS
After carrying out the operations described in 5.1 above, to replace the
heating elements proceed as follows:
- Unscrew the heating element fixing screws.
- Disconnect the heating element supply wires.
- Remove the protective casing from the heating elements.
- Remove the heating elements (item 10 plate B).
- Perform the above operations in reverse order to reassemble.
5.4 REPLACEMENT TRANSFORMER KIT PARTS 208V-240V
WARNING! For servicing the electric box on the back of 208V rated
ovens, the following operations must be performed by specialized
personnel:
-
carry out the operations indicated in point 5.1;
- disconnect the exhaust pipe, the gas and electric power supply;
- remove the oven positioning brackets and release the brakes on the
front wheels;
- then start service operations ( transformer part. 43 tav.A, fuse part. 42
tav.A, fuse carrier part. 34 tav.A );
- carry out the above operations in reverse order to restore the machine
to normal operation.
CAUTION: DISCONNECT THE POWER SUPPLY BEFORE
SERVICING AND BEFORE REPLACING FUSES AND LAMPS.
6 NOISE LEVELS
This appliance is a technical instrument of work and normally, the noise
level threshold at the operator station does not exceed 70 dB (A).
7 LIST OF SPARE PARTS
Index of plates
Plate A Baking chamber assembly
Plate B Proofer assembly
Plate C Baking chamber wiring diagram
Plate D Proofer wiring diagram
INSTRUCTIONS FOR ORDERING SPARE PARTS
Orders for spare parts must contain the following information:
- Oven serial number
- Oven type
- Name of part
- Number required