Moore UNIDRILL 300 Скачать руководство пользователя страница 26

Страница: 26 / 91

Settings

SETTINGS

Side Markers

-

Setting the markers in their working

position.

The markers are designed for marking at
the centre of the tractor.

Apply pressure to the hydraulic circuit.
Remove the locking levers

(1)

for

transport.

- Lower the first marker arm and extend
the inner arm.
(remove the pin

(2)

and loosen the

screw

(3)

this allows for infinite

horizontal adjustment of the marker
arm.

- The discs vertical setting may be
altered in order to increase or reduce
ground marking depth.

Four settings can be applied by alternating
the position of the disc orientation block

(4)

- If you wish to alter this setting move the
disc support (5) along the tube.

- The distance from the final sowing to the
disc equals half the working width plus
half the spacing.

For example 16.6 / 2 = 8.3 cm.

Secure the side markers for transport. Withdraw oil pressure before
hitching the seed drill.

Содержание UNIDRILL 300




























































































Результаты поиска

Содержание UNIDRILL 300

Отзывы:

Похожие инструкции для UNIDRILL 300

Бренды по названию

Популярные бренды

Moore UNIDRILL 300, Руководство пользователя

Результаты поиска

Содержание UNIDRILL 300

Отзывы:

Похожие инструкции для UNIDRILL 300

Бренды по названию

Популярные бренды