Monroe MR-180 Скачать руководство пользователя | Manualshive

Страница: 43 / 44

background image

39

TROUBLESHOOTING

__________________________________________________________________

In case of operational difficulty:

1.

Be sure the unit is plugged into a working electrical outlet and no other electrical device is using the same power
source. Another electrical motor on the same circuit could cause interference with register operations.

2.

Check that the Control Switch is set to the proper position.

3.

Review the operating instructions to be sure the transactions have been performed as described in this instruction
manual.

4.

If you are in the Program (PRG) or "Z" modes and the error tone sounds and the prompt "SEC Code" appears in the
display, this means a manager's security code was programmed.

5.

If the register still does not function, use the Full System Clear Procedure:

CAUTION: The Full System Clear Procedure erases all transaction data AND all programs from the memory.

A.

Turn the side switch to the "Off" position.

B. Remove the top battery and unplug the register for at least 20 minutes. (Batteries are located in the journal

compartment.)

C.

Plug the register back in and replace the battery.

D.

Reprogram the register.

6.

Call Customer Support at 1-888-666-7631.

«
...
41
42
43
44
»

Содержание MR-180













































Отзывы:

Нет отзывов

Похожие инструкции для MR-180

Бренд: TEC Страницы: 158

Бренд: Sharp Страницы: 2

Бренд: Sharp Страницы: 132

Бренд: Casio Страницы: 110

Бренд: Nautilus Hyosung Страницы: 37

Бренд: Sharp Страницы: 241

Triton 96 Series

Бренд: Dover Страницы: 62

Бренд: CEBEK Страницы: 8

DRWST-50A Series

Бренд: TOSHIBA TEC Corporation Страницы: 16

Бренд: PSG Страницы: 7

Бренд: Lighthouse Страницы: 60

Бренд: Lighthouse Страницы: 58

Бренд: Lighthouse Worldwide Solutions Страницы: 78

Бренд: Lighthouse Страницы: 82

Бренд: Lighthouse Страницы: 84

Бренд: Lighthouse Страницы: 94

Бренд: Lighthouse Страницы: 118

Handheld 3016 IAQ

Бренд: Lighthouse Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды