Monroe MR-180 Скачать руководство пользователя | Manualshive

Страница: 14 / 44

background image

10

LOADING PAPER

__________________________________________________________________

HOW TO LOAD THE PAPER

Use standard 2 1/4" single ply calculator paper to for customer receipt (outside) or a journal record (inside). Do not use two
ply paper.

NOTE: While single ply calculator tape is readily available, we recommend using Monroe MA40187 bond paper to help
prevent printer damage caused by excessive dust/lint.

Order MA40187 Paper Tape by calling Customer Support at 1 - 888-666-7631.

1.  If the MR-180 is not already plugged in, do so now.

2.  Remove the printer cover.

3.  Prepare the paper roll for loading by insuring a straight leading edge to enable proper feeding through the printer.

4.  Position the paper roll in the paper holder so that the leading edge of the paper will feed from the bottom of the roll.

5.  Insert the leading edge of the paper tape into the paper slot.

6.  Press the paper feed [Feed] key until the paper catches and advances through the printer.

7.  If the paper fails to feed, check to insure the unit is ON and the paper was installed correctly.

8.  Feed the paper up sufficiently to pass the tape through the tear off window of the printer cover. This installation is to be
used when you wish to operate the unit in customer receipt mode. REG2.

or

If customer receipts will not be generated (REG 1), insert the tape into the journal winder. Advance the tape approximately

10-12 inches by using the paper feed [Feed] key. Then, slide the tape under the two forks that extend on both sides of the
journal winder. Turn the spindle manually a few times to take up the excess paper. Then advance the paper using the
Feed key until the journal paper winds securely around the spindle.

9. Close the printer cover.

«
...
12
13
14
15
16
...
»

Содержание MR-180













































Отзывы:

Нет отзывов

Похожие инструкции для MR-180

Бренд: Nautilus Hyosung Страницы: 120

Бренд: Olivetti Страницы: 62

Euro-2000T Alpha

Бренд: ELCOM Страницы: 81

Euro-2000TE Alpha

Бренд: ELCOM Страницы: 104

Бренд: BIRD Страницы: 13

Бренд: Record Страницы: 28

Бренд: AccuBANKER Страницы: 52

Бренд: Olivetti Страницы: 55

Бренд: TEC Страницы: 84

Бренд: Sharp Страницы: 134

Бренд: Sharp Страницы: 108

ecomat 200 Series

Бренд: IFM Electronic Страницы: 25

Бренд: Sam4s Страницы: 2

Бренд: RAASM Страницы: 108

Professional 80.1078.1

Бренд: VKF Renzel Страницы: 2

SGE-353-1Y-10100M

Бренд: SGE Страницы: 8

Бренд: Red Ion Страницы: 4

PST-6000 SERIES

Бренд: POSIFLEX Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды