background image

Service check and Maintenance

It is important to carry out a regular service on your 
ergometer, to ensure it is kept in good condition.

Always keep the bike clean and well lubricated.

Service action:
• We recommend isopropyl alcohol to disinfect the 

surface of the bike. Use a damp but not wet cloth to 
clean the surface you wish to disinfect.

• Surface treatment with a rust inhibitor, especially 

when the bike is clean and the surfaces are dry This 
is done to protect the chrome and zinc parts as well 
as the painted parts (4 times per year).

• Check now and then that both pedals are firmly 

tightened. If not the threading in the pedal arms 
will be damaged. When the ergometer is new it is 
important to tighten the pedals after 5 hours of 
pedalling (check this 4 times per year).

• Check that the pedal crank is secure to the crank 

axle (4 times per year).

• Be sure that the pedals are moving smoothly, and 

that the pedal axle is clear of dirt and fibres (4 times 
per year).

• When cleaning and lubricating be sure to check that 

all screws and nuts are properly tightened (twice a 
year).

• Check that the chain is snug and there is no play in 

the pedal crank (twice a year).

• Check that pedals, chain and freewheel sprocket are 

lubricated (twice a year).

• Be sure that the brake belt does not show significant 

signs of wear (twice a year).

• Check that the handlebars and seat adjustment 

screws are lubricated (twice a year).

• Be sure that all moving parts, crank and flywheel 

are working normally and that no abnormal play 
or sound exists. Play in bearings causes fast wearing 
and with that follows a highly reduced lifetime.

• Check that the flywheel is placed in the center and 

with plane rotation.

• Grind the brake belt contact surface, see section 

"Brake belt contact surface" (once a year).

Service and Maintenance

NOTE!

Make sure the voltage indicated on the appliance 
corresponds to the local mains voltage before making 
connections. 

Note that the text about service and 
maintenance is universal and that all 
parts may not be relevant to your bike.

Warranty

EU countries - Private use

If you are a consumer living in the EU you will have 
a minimum level of protection against defects in 
accordance with EC Directive 1999/44/EC. In short, 
the directive states that your Monark dealer will be 
liable for any defects, which existed at the time of 
delivery. In case of defects, you will be entitled to have 
the defect remedied within a reasonable time, free of 
charge, by repair or replacement.

EU countries - Professional use

Monark Exercise products and parts are guaranteed 
against defects in materials and workmanship for a 
period of one year from the initial date of purchase 
of the unit. In the event of a defect in material or 
workmanship during that period, Monark Exercise 
will repair or replace the product. Monark Exercise 
will not, however, refund costs for labour or shipping. 

Other countries

Monark Exercise products and parts are guaranteed 
against defects in materials and workmanship for a 
period of one year from the initial date of purchase 
of the unit. In the event of a defect in material or 
workmanship during that period above, Monark 
Exercise will repair or replace (at its option) the 
product. Monark Exercise will not, however, refund 
costs for labour or shipping.

RC6 novo

30

Содержание novo





































Отзывы: