MK Diamond Products MK-Scarifier SG-5 Скачать руководство пользователя страница 44

Страница: 44 / 52

MK-Scarifier MaiNTeNaNce

rear Wheel change Out
NOTe:

The two (2) Rear Wheels should be replaced at the same time (MK Diamond Part # 158520).

(A)

Rotate to rest on the Handle/

Stand.

(B)

Locate the Rear Wheel

Truck Assembly.

(C)

Remove the Rear Wheel

Truck Assembly Retain-

ing Nuts using 3/4-inch

wrenches.

(D)

Remove the Rear

Wheel Truck Assembly Re-

taining Bolts.

(E)

Lower the Rear Wheel Truck

Assembly.

(F)

Remove the Rear Wheel

Retaining Cotter Pin, Shim

Washer and Rear Wheel from

each side of the Assembly.

(G)

Obtain replacement wheels.

(H)

Install the new Rear Wheel,

Shim Washer and Cotter Pin

on each side of the Assem-

bly.

(I)

Install the Rear Wheel Truck

Assembly Retaining Nuts and

Bolts removed in Steps C

and D using

3/4-inch wrenches.

Содержание MK-Scarifier SG-5





















































Результаты поиска

Содержание MK-Scarifier SG-5

Отзывы:

Похожие инструкции для MK-Scarifier SG-5

Бренды по названию

Популярные бренды

MK Diamond Products MK-Scarifier SG-5, Руководство пользователя

Результаты поиска

Содержание MK-Scarifier SG-5

Отзывы:

Похожие инструкции для MK-Scarifier SG-5

Бренды по названию

Популярные бренды