MK Diamond Products MK-Scarifier SG-5 Скачать руководство пользователя страница 36

Страница: 36 / 52

NOTe:

Refer to Engine Manual for details.

MK-Scarifier MaiNTeNaNce

Drain used oil while the engine is warm.

Conform to Federal, State and Local laws, codes and ordinances relative to

environmental protection for oil disposal.

100ºF

-20ºF

0ºF

20ºF

40ºF

60ºF

80ºF

10W-30

5W-30

-20ºC

-10ºC

0ºC

10ºC

20ºC

30ºC

40ºC

-30ºC

changing Oil
Oil is a major factor affecting performance and service life. Use 4-stroke automotive detergent oil.

Refer to Engine Manual for specific procedures. SAE 10W-30 is recommended for general use. Other

viscosity oil shown in the chart below may be used when the average temperature in your area is

within the recommended range.

NOTeS:

(A)

Lower the Scarifier to its low-

est position.

(B)

Free the Oil Drain Line.

(C)

Place a catch basin below

the Oil Drain Line and re-

move the Drain Cap using

two 1/2 –inch wrenches.

(D)

Drain Oil the engine oil (con-

form to Federal, State and

Local laws for disposal).

(E)

Using two 1/2 – inch

wrenches, install the Drain

Cap onto the Oil Drain Line

(Ensure the Cap is tight).

(F)

Fill the Oil Reservoir

(See Engine Manual).

Содержание MK-Scarifier SG-5





















































Результаты поиска

Содержание MK-Scarifier SG-5

Отзывы:

Похожие инструкции для MK-Scarifier SG-5

Бренды по названию

Популярные бренды

MK Diamond Products MK-Scarifier SG-5, Руководство пользователя

Результаты поиска

Содержание MK-Scarifier SG-5

Отзывы:

Похожие инструкции для MK-Scarifier SG-5

Бренды по названию

Популярные бренды