MK Diamond Products MK-Scarifier SG-5 Скачать руководство пользователя страница 46

Страница: 46 / 52

(J)

Locate the V-belt Adjust-

ing Screw inside the Cut-

ting Drum Well. Loosen the

screw using a 9/16-inch

wrench.

(K)

Remove the V-belt from the

Engine and Cutting Drum

Pulleys.

(L)

Clean and verify the align-

ment of the Engine and Cut-

ting Drum Pulleys.

(M)

Obtain and install a new

V-belt onto the Engine and

Cutting Drum Pulleys.

(N)

Verify the V-belt is seated in

all grooves of the Engine and

Cutting Drum Pulleys.

(O)

Pull the front of the Engine

Mounting Plate away from

the Frame to tension the

V-belt.

(P)

Tighten the V-belt Adjust-

ing Screw one turn using a

9/16-inch wrench.

(Q)

Verify the tension of the

V-belt (proper tension is

1/2-inch deflection of

the belt).

(R)

Repeat Steps P and Q until

proper tension has been

reached (proper tension is

1/2-inch deflection of the

belt).

MK-Scarifier MaiNTeNaNce

Содержание MK-Scarifier SG-5





















































Результаты поиска

Содержание MK-Scarifier SG-5

Отзывы:

Похожие инструкции для MK-Scarifier SG-5

Бренды по названию

Популярные бренды

MK Diamond Products MK-Scarifier SG-5, Руководство пользователя

Результаты поиска

Содержание MK-Scarifier SG-5

Отзывы:

Похожие инструкции для MK-Scarifier SG-5

Бренды по названию

Популярные бренды