MK Diamond Products MK-Scarifier SG-5 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 52

background image

25

MK-Scarifier aSSeMBLY

fiLLiNg fUeL TaNK

1.

Gasoline is highly flammable and explosive. You can be burned or seriously

injured when handling fuel.

2.

To fuel, stop engine if running, and allow it to cool.

3.

Refuel in a well-ventilated area.

4.

Keep gasoline away from appliance pilot lights, barbecues, electric

appliances, power tools, etc.

5.

Wipe up spills immediately.

1.

Fuel can damage paint and plastic. Be careful not to spill fuel when filling the fuel

tank. Damage caused by spilled fuel IS NOT covered under the warranty.

2.

DO NOT use stale or contaminated gasoline, or an oil/gasoline mixture.

3.

Use unleaded gasoline with a pump octane rating of 86 or higher.

NOTeS:

NOTe:

WarNiNg

Refer to Engine Manual for details.

VacUUM SeTUP fOr OPeraTiON
The Scarifier is designed for use with a vacuum. MK Diamond recommends using a vacuum to re-

duce the amount of dust generated during operation.

MK Diamond does not endorse any specific vacuum type, but does recommend the customer use the

Scarifier with a dry dust collector (designed for wood dust) as opposed to a standard wet/dry vacuum.

(A)

Obtain a vacuum or dust

collection system.

(B)

Remove the Cap from the

Vacuum Connection Point.

(C)

Using a 2 1/2-inch hose,

connect the Vacuum to the

Scarifier at the Vacuum

Connection Point.

(D)

Verify the hose connections

are secure at the Scarifier

and the Vacuum.

«
...
23
24
25
26
27
...
»

Содержание MK-Scarifier SG-5





















































Отзывы:

Нет отзывов

Похожие инструкции для MK-Scarifier SG-5

Бренд: OKIFAX Страницы: 147

Бренд: Baby Lock Страницы: 6

Бренд: Baby Lock Страницы: 20

imagine wave BLE3ATW

Бренд: Baby Lock Страницы: 18

Бренд: Baby Lock Страницы: 16

Бренд: Baby Lock Страницы: 36

Бренд: Baby Lock Страницы: 40

Embroidery Professional BMP8

Бренд: Baby Lock Страницы: 32

ellure plus BLR2

Бренд: Baby Lock Страницы: 32

ellure plus BLR2

Бренд: Baby Lock Страницы: 195

Бренд: Baby Lock Страницы: 28

ellegante BLG guid

Бренд: Baby Lock Страницы: 241

ellegante 2 BLG2

Бренд: Baby Lock Страницы: 56

Elizabeth BL200A

Бренд: Baby Lock Страницы: 152

Бренд: Baby Lock Страницы: 42

Ellisimo Gold II

Бренд: Baby Lock Страницы: 2

Бренд: Kärcher Страницы: 312

Бренд: Nancy’s Knit Knacks Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды