manualshive.com logo in svg

Miyachi Unitek LMV700, Руководство оператора

Поделиться
Скачать
Miyachi Unitek LMV700 Скачать руководство пользователя страница 15

CHAPTER 1:  SYSTEM DESCRIPTION 

LMV700 Nd:YVO

4

 LASER MARKER 

990-545

1-3

Section II:  Part Names and Functions 

Control Unit  (Front) 

Incorporates the controller, electronic cooling unit, RF unit, and power supply unit.  You can monitor 
the operating status from a computer. 

1.

Emergency Stop Button 

Press to stop all marking processes immediately during an emergency.  This will immediately 
suspend marking and turn the LD OFF.  Once pressed, the button will remain depressed.  To reset 
this button, turn the knob in the direction indicated by the arrows. 

CAUTION

Use this button to stop the device 

only

 in emergency situations.  Frequent use of the 

emergency stop button will significantly affect the LD service life. 

2.

Main Switch 

Turn to the ON position to supply power.  Turn to the OFF position to cut the power supply and 
stop the unit. 

Содержание LMV700









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды