Mitsubishi MOTORS Lancer 2004 Скачать руководство пользователя страница 207

Страница: 207 / 638

FRONT AXLE HUB ASSEMBLY

FRONT AXLE

26-13

REASSEMBLY SERVICE POINTS
>>A<< WHEEL BEARING INSTALLATION

1. Fill the wheel bearing with multipurpose grease.
2. Apply a thin coating of multipurpose grease to the

knuckle and bearing contact surfaces.

CAUTION

Press the outer race when pressing-in the wheel
bearing. Otherwise the wheel bearing will be
damaged.

3. Press-in the bearing by using the following special

tools.

•

Rear suspension bushing arbor (MB990883)

•

Rear suspension bushing base (MB990890)

>>B<< HUB STARTING TORQUE CHECK

1. Tighten the following special tools to the specified

torque, and then press-in the hub into the knuckle.

•

Front hub remover and installer (MB991017)

•

Spacer (MB991000)

2. Rotate the hub in order to seat the bearing.

3. Measure the hub starting torque by using the

following special tools.

•

Torque wrench (MB990685)

•

Preload socket (MB990326)

Limit: 1.8 N

⋅

4. The starting torque must be within the limit and

the hub rotation must be smooth.

>>C<< WHEEL BEARING AXIAL PLAY
CHECK

1. Measure to determine whether the wheel bearing

axial play is within the limit or not by using the
following special tools.

•

Front hub remover and installer (MB991017)

•

Spacer (MB991000)

Limit: 0.05 mm

2. If the play is not within the limit range while the nut

is tightened to 245

29 N

⋅

m, the bearing, hub

and/or knuckle have probably not been installed
correctly. Replace the bearing and re-install.

INSPECTION

M1261002000078

•

Check the front hub and brake disc mounting
surfaces for galling and contamination.

•

Check the knuckle inner surface for galling and
cracks.

AC102511

MB990883

MB990890

AC210929AC

MB991000

MB991017

245 ± 29 N

Tighten the nut
with the bolt secured

AC100136

MB990685

MB990326

AC100137

MB991000

MB991017

245 ± 29 N

Tighten the nut
with the bolt
secured

Содержание Lancer 2004































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Lancer 2004

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi MOTORS Lancer 2004, Руководство по ремонту

Результаты поиска

Содержание Lancer 2004

Отзывы:

Бренды по названию

Популярные бренды