Mitsubishi Electric PUMY-P200YKM2-BS Скачать руководство пользователя страница 133

Страница: 133 / 135

OPERATING PROCEDURE

PHOTOS/FIGURES

9. Removing bypass valve coil (SV1) and bypass valve

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Remove the electrical parts box. (See Photo 5)

(4) Remove the cover panel (front). (Refer to procedure 8 (5))

(5) Remove the cover panel (rear). (Refer to procedure 8 (6))

(6) Remove the side panel (R). (Refer to procedure 8 (7))

(7) Remove the bypass valve coil fixing screw (M4 × 6).

(8) Remove the bypass valve coil by sliding the coil upward.

(9) Recover refrigerant.

(10) Remove the welded part of bypass valve.

Refer to the notes below.

Photo 11

Photo 12

10. Removing the high pressure switch (63H)

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Remove the electrical parts box. (See Photo 5)

(4) Remove the cover panel (front). (Refer to procedure 8 (5))

(5) Remove the cover panel (rear). (Refer to procedure 8 (6))

(6) Remove the side panel (R). (Refer to procedure 8 (7))

(7) Pull out the lead wire of high pressure switch.

(8) Recover refrigerant.

(9) Remove the welded part of high pressure switch.

Refer to the notes below.

11. Removing the low pressure sensor (63LS) and high

pressure sensor (63HS)

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Remove the electrical parts box. (See Photo 5)

(4) Remove the cover panel (front). (Refer to procedure 8 (5))

(5) Remove the cover panel (rear). (Refer to procedure 8 (6))

(6) Remove the side panel (R). (Refer to procedure 8 (7))

(7) Recover refrigerant.

(8) Remove the welded part of low pressure sensor and high

pressure sensor.

Refer to the notes below.

12. Removing linear expansion valve (LEV-A, LEV-B)

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Remove the electrical parts box. (See Photo 5)

(4) Remove the cover panel (front). (Refer to procedure 8 (5))

(5) Remove the cover panel (rear). (Refer to procedure 8 (6))

(6) Remove the side panel (R). (Refer to procedure 8 (7))

(7) Remove the linear expansion valve coil. (See Photo 12)

(8) Recover refrigerant.

(9) Remove the welded part of linear expansion valve.

Notes:

Recover refrigerant without spreading it in the air.

The welded part can be removed easily by removing the

right side panel.

When installing the following parts, cover it with a wet

cloth to prevent it from heating as the temperature below,

then braze the pipes so that the inside of pipes are not

oxidized;

• Bypass valve (procedure 9), 120°C or more

• High pressure switch (procedure 10), 100°C or more

• Low pressure sensor and high pressure sensor

(procedure 11), 100°C or more

• Linear expansion valve (procedure 12), 100°C or more

13. Removing the reactor (DCL)

(1) Remove the service panel. (See Photo 1)

(2) Disconnect the lead wires from the reactor. (See Photo5)

(3) Disconnect the connectors of reactor on the bottom plate

of the electrical parts box. (See Photo13)

(4) Remove 4 screws on the bottom plate of the electrical

parts box. (See Photo 13)

(5) Remove the reactor.

Photo 13

High pressure

sensor (63HS)

High

pressure

switch (63H)

Low pressure

sensor

(63LS)

Bypass valve

coil fixing screw

Bypass valve

coil (SV1)

Bypass

valve

Low pressure

sensor (63LS)

Linear expansion

valve coil (LEV-A)

Linear

expansion valve

Linear expansion

valve coil (LEV-B)

Linear

expansion valve

Reactor

Screws

Connectors

of reactor

Bottom

plate of

electrical

parts box

Electrical parts box

133

OCH675E

Содержание PUMY-P200YKM2-BS








































































































































Результаты поиска

Содержание PUMY-P200YKM2-BS

Отзывы:

Mitsubishi Electric PUMY-P200YKM2-BS, Техническое и сервисное руководство, Страница: 133 / 135

Результаты поиска

Содержание PUMY-P200YKM2-BS

Отзывы: