Mitsubishi Electric PUMY-P200YKM2-BS Скачать руководство пользователя страница 102

Страница: 102 / 135

102

OCH675E

Check method of DC fan motor (fan motor/outdoor multi controller circuit board)

Notes

· High voltage is applied to the connector (CNF1, 2) for the fan motor. Pay attention to the service.

· Do not pull out the connector (CNF1, 2) for the motor with the power supply on.

(It causes trouble of the outdoor multi controller circuit board and fan motor.)

Self check

Symptom: The outdoor fan cannot rotate.

Correct the wiring.

Replace the outdoor multi

controller circuit board (MULTI.B.).

Is the fan motor

normal?

Yes

Fail

Fuse check

Check the fuse (F500) on outdoor

multi controller circuit board.

Replace the outdoor multi

controller circuit board (MULTI.B.)

and the defective fan motor.

Disconnect the FAN motor connector and

measure the resistance of connector pins.

Refer to “8-7. HOW TO CHECK THE PARTS”.

Wiring contact check

Contact of fan motor connector

(CNF1,2)

Did the fuse blow?

Is there contact failure?

Is the voltage normal?

Replace the defective fan motor.

Replace the outdoor multi

controller circuit board.

Check the operation.

Complete.

Replace the defective fan motor.

Replace the outdoor multi

controller circuit board.

Check the operation of fan.

Power supply check (Remove the connector (CNF1,2))

While the breaker is OFF, disconnect the compressor wirings (U/V/W) from the outdoor power circuit board.

While the breaker is OFF, disconnect the fan motor connector CNF1,2.

When 5 minutes have passed since turning ON the breaker, turn SW7-1 ON.

Check the voltage of the outdoor multi controller circuit board.

Measure the voltage in the outdoor controller circuit board.

TEST POINT 1 : VDC (between 1 (+) and 4 (−) of the fan connector): 310–340 V DC (Y)

: VDC (between 1 (+) and 4 (−) of the fan connector): 310-340 V DC (when PAM stops), 380 V DC (when PAM is operating) (V)

TEST POINT 2 : VCC (between 5 (+) and 4 (−) of the fan connector): VCC 15 V DC

TEST POINT 3 : VCC (between 6 (+) and 4 (−) of the fan connector): VCC 0–6.5 V DC

Note: Turn SW7-1 OFF after the troubleshooting completes.

Содержание PUMY-P200YKM2-BS








































































































































Результаты поиска

Содержание PUMY-P200YKM2-BS

Отзывы:

Mitsubishi Electric PUMY-P200YKM2-BS, Техническое и сервисное руководство, Страница: 102 / 135

Результаты поиска

Содержание PUMY-P200YKM2-BS

Отзывы: