Mitsubishi Electric PUMY-P200YKM2-BS страница 132 Скачать руководство пользователя

Страница: 132 / 135

OPERATING PROCEDURE

PHOTOS/FIGURES

6. Removing the thermistors

Thermistor <HIC> (TH2) and thermistor <Compressor> (TH4)

(1) Remove the service panel. (See Photo 1)

(2) Disconnect the connectors, TH2 (black) and TH4 (white),

on the Multi controller board in the electrical parts box.

(3) Loosen the clamp for the lead wire in the rear of the elec

trical parts box.

(4) Pull out the thermistor <HIC> (TH2) and thermistor

<Compressor> (TH4) from the sensor holder. (See Photo

9-1)

Thermistor <Outdoor pipe> (TH3)

(1) Remove the service panel. (See Photo 1)

(2) Disconnect the connector, TH3 (white), on the Multi con

troller board in the electrical parts box.

(3) Loosen the clamp for the lead wire in the rear of the elec

trical parts box.

(4) Pull out the thermistor <Outdoor pipe> (TH3) from the

sensor holder. (See Photo 9-2)

Photo 9-1

Photo 9-2

7. Removing the 4-way valve coil (21S4)

(1) Remove the service panel. (See Photo 1)

[Removing the 4-way valve coil]

(2) Remove 4-way valve coil fixing screw (M5 × 7).

(3) Remove the 4-way valve coil by sliding the coil toward

you.

(4) Disconnect the connector 21S4 (green) on the outdoor

multi controller circuit board in the electrical parts box.

8. Removing the 4-way valve

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Remove the electrical parts box. (See Photo 5)

(4) Remove 3 valve bed fixing screws (4 × 10) and 4 ball

valve and stop valve fixing screws (5 × 16) and then

remove the valve bed. (See Photo 4 and 7)

(5) Remove 2 cover panel fixing screws (5 x 12), then slide

the cover panel (front) upward to remove it. (The cover

panel (front) is fixed to the cover panel (rear) with a hook

on the rear side. (See Photo 4)

(6) Remove the cover panel (rear) fixing screws (2 for right

side and 2 for rear/ 5 x 12), then slide the cover panel

(rear) upward to remove it. (See Photo 4) (The cover

panel (rear) is fixed to the side panel (R) with 2 screws.)

(7) Remove 3 side panel (R) fixing screws (5 × 12) in the

rear of the unit, then slide the side panel (R) upward to

remove it. (The side panel (R) is fixed to the side plate

with hooks on the rear side.)

(8) Remove the 4-way valve coil. (See Photo 10)

(9) Recover refrigerant.

(10) Remove the welded part of 4-way valve.

Note 1: Recover refrigerant without spreading it in the air.

Note 2: The welded part can be removed easily by remov

ing the right side panel.

Note 3: When installing the four-way valve, cover it with

a wet cloth to prevent it from heating (120°C or

more), then braze the pipes so that the inside of

pipes are not oxidized.

Photo 10

4-way valve coil

(21S4)

4-way valve

4-way valve coil

fixing screw

Thermistor

(TH4)

Thermistor

<HIC> (TH2)

Compressor

(MC)

Thermistor

(TH3)

132

OCH675E

Содержание PUMY-P200YKM2-BS








































































































































Результаты поиска

Содержание PUMY-P200YKM2-BS

Отзывы:

Похожие инструкции для PUMY-P200YKM2-BS

Бренды по названию

Популярные бренды

Mitsubishi Electric PUMY-P200YKM2-BS, Техническое и сервисное руководство

Результаты поиска

Содержание PUMY-P200YKM2-BS

Отзывы:

Похожие инструкции для PUMY-P200YKM2-BS

Бренды по названию

Популярные бренды