Mitsubishi Electric PUMY-P200YKM2-BS страница 87 Скачать руководство пользователя

Страница: 87 / 135

Check code

Chart 1 of 2

6832(E3/E5)

6833(E3/E5)

MA communication send error

Abnormal points and detection methods

Causes and checkpoints

Detected in remote controller or indoor unit.

There are 2 remote controllers set as main.

Malfunction of remote controller sending/receiving

circuit

Malfunction of sending/receiving circuit on indoor

controller board

Remote controller transmitting error caused by noise

interference

●Diagnosis of defects

Make sure to turn the power OFF before connecting/disconnecting any connectors, or replacing boards

Diagnosis

Remedy

Set one remote controller to main remote

controller, and the other to sub.

Note:

It takes 6 seconds at maximum

until the result is displayed.

No abnormality

A connector or wiring contact failure is

suspected.

Yes

Continue to the next page.

No abnormality

It might be caused by an external noise, so

check the transmission line.

Yes

Replace the remote controller.

Replace the indoor controller board with

the LED2 is blinking.

Yes

OCH675E

Check the remote controller for

main-sub setting.

Conduct the Remote Controller

Diagnosis more than 2 times.

Is the check code

<6832> or <6833> still

displayed?

Is there only 1 remote controller

set as the main controller?

Disconnect and reconnect the

connector CN3A, then turn the

power back ON.

Is "NG" displayed?

Turn the power back ON

Is "6832" or "ERC"

displayed?

Does "Please Wait"

disappear within

6 minutes?

Is "OK" displayed on all

remote controllers?

Содержание PUMY-P200YKM2-BS








































































































































Результаты поиска

Содержание PUMY-P200YKM2-BS

Отзывы:

Похожие инструкции для PUMY-P200YKM2-BS

Бренды по названию

Популярные бренды

Mitsubishi Electric PUMY-P200YKM2-BS, Техническое и сервисное руководство

Результаты поиска

Содержание PUMY-P200YKM2-BS

Отзывы:

Похожие инструкции для PUMY-P200YKM2-BS

Бренды по названию

Популярные бренды