Mitsubishi Electric PUMY-P200YKM2-BS страница 42 Скачать руководство пользователя

Страница: 42 / 135

OCH675E

8-1-1-2. Test run for MA remote controller <PAR-4xMAA (˝x˝ represents 0 or later)>

Test run menu

Cursor

Service menu:

Test run

Drain pump test run

Select ˝

Service

˝ from the Main menu, and press the

[ ] button.

Select ˝Test run˝ with the F1

or F2 button, and press the [ ] button.

Select ˝Test run˝ with the F1

or F2 button, and press the [ ] button.

Cool

Pipe

Auto

Switch disp.

Mode

Fan

Remain

Test run

Remain

Vane

Test run

Cool mode:

Check the cold air blows out.

Heat mode:

Check the heat blows out.

Press the

F1 button to go through the operation modes in the order of ˝Cool

and Heat˝.

Check the auto vane with the F1

F2 buttons.

Press the [

] button to return to ˝Test run operation˝.

Press the

button.

When the test run is completed, the ˝Test run menu˝ screen will appear.

The test run will stop automatically after 2 hours.

*The function is available only for the model with vanes.

Test run operation

Auto vane check

Press the [ ] button and open the Vane setting screen.

Function buttons

MENU RETURN SELECT ON/OFF

Check the operation of the outdoor unit’s fan.

Test run

Input maintenance info.

Settings

Check

Others

Содержание PUMY-P200YKM2-BS








































































































































Результаты поиска

Содержание PUMY-P200YKM2-BS

Отзывы:

Похожие инструкции для PUMY-P200YKM2-BS

Бренды по названию

Популярные бренды

Mitsubishi Electric PUMY-P200YKM2-BS, Техническое и сервисное руководство

Результаты поиска

Содержание PUMY-P200YKM2-BS

Отзывы:

Похожие инструкции для PUMY-P200YKM2-BS

Бренды по названию

Популярные бренды